Adjusting the position
DOT CLOCK
(RGB only)
Picture | Operation | |
condition | ||
|
When the input signal is RGB, first press the AUTO SETUP button to initiate automatic positioning.
If the optimum setting is not obtained when AUTO SETUP is carried out, adjust by the following procedure.
Select the item pressing the F or G buttons on the remote control unit or the projector.
Press the I or H buttons, to adjust the alternative items. For the numerically adjustable items, press the ENTER button to display an individual screen, and press the I or H buttons to adjust the setting. Some items can be adjusted pressing the F or G buttons.
When an RGB signal is being input
POSITION
POSITION | H: | 128 | V: | 32 |
DOT CLOCK | 32 |
|
|
|
CLOCK PHASE | 16 |
|
|
|
KEYSTONE | H: | 0 | V: | 0 |
OSD POSITION |
| TOP LEFT |
| |
RESIZING |
| OFF | ON |
|
AUTO SETUP |
|
|
|
|
FRAME LOCK |
| OFF | ON |
|
STANDARD |
|
|
|
|
SELECT:[^][@] |
| ENTER:[ENTER] |
| |
ADJUST:[{][}] |
| ESC:[MENU] |
| |
When a YPBPR signal is being input.
POSITION
POSITION | H: | 64 | V: | 16 |
KEYSTONE | H: | 0 | V: | 0 |
OSD POSITION |
| TOP LEFT |
| |
ASPECT |
|
| 4:3 |
|
RESIZING |
| OFF | ON |
|
AUTO SETUP |
|
|
|
|
STANDARD |
|
|
|
|
SELECT:[^][@] ENTER:[ENTER]
ADJUST:[{][}] ESC:[MENU]
When an S-VIDEO/VIDEO signal is being input
POSITION
POSITION | H: | 32 | V: | 16 |
KEYSTONE | H: | 0 | V: | 0 |
OSD POSITION |
| TOP LEFT |
| |
ASPECT |
| AUTO |
|
|
RESIZING |
| OFF | ON |
|
AUTO SETUP |
|
|
|
|
STANDARD |
|
|
|
|
SELECT:[^][@] ENTER:[ENTER]
ADJUST:[{][}] ESC:[MENU]
When the NETWORK/SD CARD is selected
POSITION
KEYSTONE | H: | 0 | V: | 0 |
OSD POSITION |
| TOP LEFT |
| |
AUTO SETUP |
|
|
|
|
STANDARD |
|
|
|
|
SELECT:[^][@] ENTER:[ENTER]
ADJUST:[{][}] ESC:[MENU]
POSITION
Moves the picture position.
Press the I or H buttons to move the picture horizontally.
Press the F or G buttons to move the picture vertically.
H: 128
POSITION V: 32
Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, use the
Iand H buttons to adjust so that any such noise is minimised.
CLOCK PHASE
(RGB only)
Adjust the DOT CLOCK setting first before carrying out this adjustment. Use the I and H buttons to adjust so that the noise level is least noticeable.
NOTE:
BIf signals with a dot clock frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the DOT CLOCK and CLOCK PHASE adjustments are carried out.
KEYSTONE
Before carrying out keystone correction, 1) adjust the forward/back angle of tilt of the projector by pressing the adjuster buttons and 2) press the AUTO SETUP buttons to correct vertical keystone distortion. (page 27)
The vertical keystone distortion will be automatically corrected by the projectors automatic setup function. However the horizontal distortion needs to be corrected or a tilted screen needs to be adjusted manually by following any of the procedures in the table.
KEYSTONE H: 0
V: 0
Press the F button.
Press the G button.
Press the I button.
Press the H button.
NOTE:
BIf you press the AUTO SETUP button | settings | |
after correcting the keystone distortion | ||
| ||
manually, the automatic keystone |
| |
correction function will operate and the | and | |
corrected picture will return to its | ||
previous incorrect condition. In addition, | Adjustments | |
if you change the input signal and press | ||
|
the AUTO SETUP button, the keystone correction may be cancelled depending on the type of signal and the angle of tilt of the projector. To prevent them from happening, you can set “AUTO KEYSTONE” in the OPTION menu to “OFF”
BThe greater the correction of keystone distortion amount, the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as
|
|