Nortel Networks 400-S manual Modular components used in this assembly

Page 4

4

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.

Notice: For equipment using loopstart lines, please note that the Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN is located on the "FCC Rules Part 68" label located on the bracket of the module or on the back of the unit.

Canada CS-03 -- Règles et règlements

Avis: L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de protection, d'exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n'assure toutefois pas que le matériel fonctionnera à la satisfaction de l'utilisateur.

Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de raccordement. L'abonné ne doit pas oublier qu'il est possible que la conformité aux conditions énoncées ci-dessus n'empêche pas la dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur. L'entreprise de télécommunications peut demander à l'utilisateur de débrancher un appareil à la suite de réparations ou de modifications effectuées par l'utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la source d'énergie électrique, des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissement: L'utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service d'inspection des installations électriques, ou à un électricien, selon le cas.

Avis: Veuillez prendre note que pour tout appareillage supportant des lignes de type "loopstart," l'indice d'équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d'une interface téléphonique peut consister en une combinaison de quelques dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas 5. Le REN figure sur l'étiquette "FCC Rules Part 68" située sur le support du module ou à l'arrière de l'unité.

Modular components used in this assembly

This product contains a base unit and possibly one or more of the following Communication and Network Connection Options Devices. Please refer to your specific product for a description of what option cards (if any) are included. Compliance Statements for all the following devices are on file and available on request.

FCC Part 68 compliance statement

This equipment complies with Part 68 of FCC Rules. All direct connections to telephone network lines must be made using standard plugs and jacks compliant with FCC Part 68. Please note the following:

209375-A

Image 4
Contents Setting Up the BayStack Instant Internet 400-S Unit USA requirements only Japan/Nippon requirements only Modular components used in this assembly Setting Up the BayStack Instant Internet 400-S Unit UL listing/C-UL listing NT1 Instant Internet Isdn Device Nortel Networks NA Inc. software license agreement Setting Up the BayStack Instant Internet 400-S Unit 209375-A Contents Chapter Seven-port autosensing switch specifications Appendix a Technical specifications Contents 209375-A Figures Figures 209375-A Tables Tables 209375-A Preface Before you beginAcronyms Following acronyms are used in this manualRelated publications Preface How to get help Preface 209375-A Chapter Introduction Instant Internet packageAvailable options Requirements and compatibility Introduction 209375-A Chapter Installation preparation Preparing for Internet accessSelecting an Internet service provider Making decisionsInstallation checklist Installation checklistInstallation preparation Installation checklist Installation worksheet ISP InformationIs Isdn Dial backup available if requested Chapter Instant Internet 400-S hardware installation Getting to know your Instant Internet 400-S unitDIP switches see , DIP switch settings, on Interfaces Rear panel of the Instant Internet 400-S unitEthernet interfaces Power cords Isdn S/TLists specifications for international power cords Achtung Bitte sofort lesen Setting the voltage selector switch Attenzione Leggere attentamenteInstant Internet quick installation Instant Internet 400-S hardware installation Instant Internet 400-S hardware installation Mounting your Instant Internet unit in a rack Removing screws from cover of Instant Internet 400-S unit 9863FB 10045FA Instant Internet 400-S hardware installation 209375-A Chapter Seven-port autosensing switch specifications Instant Internet 10/100 Ethernet switch overviewSwitch features RJ-45 10BASE-T/100BASE-TX Ethernet portsMDI/MDI-X autosensing capability LEDsSeven-port autosensing switch specifications 209375-A Chapter DIP switch settings DIP switchesSwitch settings for normal operation Switch settings for special configurationsDIP switch settings Resetting your Instant Internet unit Refer to Switch settings for special configurations onDIP switch settings DIP switch settings 209375-A Chapter LEDs support and diagnostic functions Interpreting Instant Internet LEDsLEDs 1 through 8 and Power LED at power-up sequence LEDs support and diagnostic functionsLEDs 1 through 8 and the Power LED during operation LED status and appearance during operationSeven-port switch port status LEDs Chapter Out-of-band management support Connecting a PC to the Instant Internet unit Configuring a direct connectionHyperTerminal Connection Description dialog box HyperTerminal Connect To dialog box Command prompt Connecting a modem to a PC Configuring modem connection settingsHyperTerminal Connection Description dialog box Ats0=1&w\r Connecting to an Instant Internet unit Connecting a modem to the Instant Internet unitOut-of-band management support 209375-A Physical specifications Appendix a Technical specificationsElectrical specifications Environmental specifications Direct access adapter cables Appendix B Adapter cable pinout diagramsCable part numbers 35 adapter cable pinout diagram Adapter cable21 DCE adapter cable diagram DCE adapter cableRemote access adapter cables Null modem adapter PC-to-PC cableModem adapter cable pinout diagram Modem adapter cableAppendix B Adapter cable pinout diagrams 209375-A Symbols NumbersIndex Index Index