Nortel Networks 400-S manual Resetting your Instant Internet unit

Page 58

58Chapter 5 DIP switch settings

Table 10 shows the switch settings for resetting your unit to factory default conditions.

Table 10 Switch settings for resetting factory default conditions

 

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

Caution: If you use these switch settings to reset your unit to factory default conditions, the following user-defined settings are removed or reset: password, hosts, port mappings, unit configuration, access restrictions, unit registration, and encryption authorization.

If you purchased and installed the 3DES Encryption Module (part number

CQ1010005), you need to reinstall it.

If you used the switch settings in Table 9 to disable the reset password and configuration switch settings, these settings are re-enabled.

Resetting your Instant Internet unit

Before you reset your Instant Internet unit, be sure to back up the configuration. If you back up the configuration, you can easily restore it. For details, refer to Using the BayStack Instant Internet Management Software Version 7.11.

To reset your Instant Internet unit:

1Turn off your unit.

2Set the switches to the configuration you want.

Refer to “Switch settings for special configurations” on page 56.

209375-A

Image 58
Contents Setting Up the BayStack Instant Internet 400-S Unit USA requirements only Japan/Nippon requirements only Modular components used in this assembly Setting Up the BayStack Instant Internet 400-S Unit UL listing/C-UL listing NT1 Instant Internet Isdn Device Nortel Networks NA Inc. software license agreement Setting Up the BayStack Instant Internet 400-S Unit 209375-A Contents Chapter Seven-port autosensing switch specifications Appendix a Technical specifications Contents 209375-A Figures Figures 209375-A Tables Tables 209375-A Preface Before you beginAcronyms Following acronyms are used in this manualRelated publications Preface How to get help Preface 209375-A Chapter Introduction Instant Internet packageAvailable options Requirements and compatibility Introduction 209375-A Chapter Installation preparation Preparing for Internet accessSelecting an Internet service provider Making decisionsInstallation checklist Installation checklistInstallation preparation Installation checklist Installation worksheet ISP InformationIs Isdn Dial backup available if requested Chapter Instant Internet 400-S hardware installation Getting to know your Instant Internet 400-S unitDIP switches see , DIP switch settings, on Interfaces Rear panel of the Instant Internet 400-S unitEthernet interfaces Power cords Isdn S/TLists specifications for international power cords Achtung Bitte sofort lesen Setting the voltage selector switch Attenzione Leggere attentamenteInstant Internet quick installation Instant Internet 400-S hardware installation Instant Internet 400-S hardware installation Mounting your Instant Internet unit in a rack Removing screws from cover of Instant Internet 400-S unit 9863FB 10045FA Instant Internet 400-S hardware installation 209375-A Chapter Seven-port autosensing switch specifications Instant Internet 10/100 Ethernet switch overviewSwitch features RJ-45 10BASE-T/100BASE-TX Ethernet portsMDI/MDI-X autosensing capability LEDsSeven-port autosensing switch specifications 209375-A Chapter DIP switch settings DIP switchesSwitch settings for normal operation Switch settings for special configurationsDIP switch settings Resetting your Instant Internet unit Refer to Switch settings for special configurations onDIP switch settings DIP switch settings 209375-A Chapter LEDs support and diagnostic functions Interpreting Instant Internet LEDsLEDs 1 through 8 and Power LED at power-up sequence LEDs support and diagnostic functionsLEDs 1 through 8 and the Power LED during operation LED status and appearance during operationSeven-port switch port status LEDs Chapter Out-of-band management support Connecting a PC to the Instant Internet unit Configuring a direct connectionHyperTerminal Connection Description dialog box HyperTerminal Connect To dialog box Command prompt Connecting a modem to a PC Configuring modem connection settingsHyperTerminal Connection Description dialog box Ats0=1&w\r Connecting to an Instant Internet unit Connecting a modem to the Instant Internet unitOut-of-band management support 209375-A Physical specifications Appendix a Technical specificationsElectrical specifications Environmental specifications Direct access adapter cables Appendix B Adapter cable pinout diagramsCable part numbers 35 adapter cable pinout diagram Adapter cable21 DCE adapter cable diagram DCE adapter cableRemote access adapter cables Null modem adapter PC-to-PC cableModem adapter cable pinout diagram Modem adapter cableAppendix B Adapter cable pinout diagrams 209375-A Symbols NumbersIndex Index Index