Nortel Networks 1000BASE-XD, 8100 manual Passport 8148TX 48-Port I/O Module

Page 31

About the Passport 8100 Modules

Passport 8148TX 48-Port I/O Module

The Passport 8148TX module provides 48 autonegotiating 10/100 Mb/s ports

(Figure 1-5). Each port can operate in full- or half-duplex mode. Autonegotiation circuitry automatically negotiates the highest possible data rate and the duplex operation possible with the attached device, if the attached device supports IEEE 802.3u autonegotiation.

9672EA

Figure 1-5. Passport 8148TX Edge Switch Module

The port connectors are modular RJ-45 connectors with MDI-X wiring. This port can be connected to an MDI port (for example, a workstation or server) using a straight-through cable.

The Passport 8108TX module uses 10BASE-T/100BASE-TX RJ-45 port connectors to connect to 10 Mb/s or 100 Mb/s Ethernet segments or nodes.

Note: For 10 Mb/s connections, you can use Category 3, 4, or 5 copper unshielded twisted pair (UTP) cable. Use only Category 5 UTP cable to connect ports that will operate at 100 Mb/s.

Refer to Appendix A, “Technical Specifications,” for more information about the RJ-45 port connectors.

204515-C

1-11

Image 31

Contents Using the Passport 8100 Modules EC Declaration of Conformity EN 55 022 StatementBureau of Standards, Metrology and Inspection Bsmi Statement Voluntary Control Council for Interference Vcci Statement204515-C 204515-C 204515-C Contents Chapter Installing a Passport 8100 Module Appendix a Technical Specifications Appendix C Media Dependent Adapters Figures Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Tables Xiv Before You Begin PrefaceItalic text Text ConventionsRelated Publications Xviii Technical Solutions Center Telephone Number How to Get HelpPage Chapter About the Passport 8100 Modules Features About the Passport 8100 Modules Passport 8190SM Management Module Passport 8190SM Switch Management ModuleEthernet Management Port Pcmcia Card Slot DTE/DCE SwitchReset Button Serial PortsLEDs on the Passport 8190SM Module LEDsPassport 8132TX 32-Port I/O Module 10BASE-T/100BASE-TX Port ConnectorsComm Port MDA SlotLEDs on the Passport 8132TX Module Passport 8148TX 48-Port I/O Module Passport 8148TX Edge Switch ModuleLEDs on the Passport 8148TX Module Passport 8108GBIC 8-Port I/O ModulePassport 8108GBIC Module Redundancy FeaturesRedundant Passport 8190SM Modules Redundant Power SuppliesChassis Number Hot-Swap One? Modules Power Supplies Power Supply Hot-SwappingCombining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Safety and Environmental Precautions Chassis Configuration RequirementsRemoving a Filler Panel Installing a ModuleSlide the module into the slot Figure Securing the Module in the Chassis Turning On the Chassis PowerConnecting Cables Routing Network Cables Replacing ModulesTo replace a module Chapter Basic Switch Configuration Port Numbers on High-Density Modules Specifying Port NumbersBooting the Switch Access Level Description Default Login Password Access Levels and Default Login ValuesLogging On to the System Assigning an IP Address to the Management Port Setting System IdentificationChange CLI users and passwords using the following commands Setting System SecurityChange Web passwords using the command To assign an IP address for management, use the command Switch ConfigurationSpecify a default gateway address/default route Page Normal Power-Up Sequence Chapter TroubleshootingLED Indications of Problems Failure to Get a Login Prompt from the Console PortFailure of Management Software to Recognize I/O Modules Symptom Probable Cause Corrective Action LED Indications of ProblemsCabling Port Connection ProblemsAutonegotiation Modes Port Interface Use the CLI to disable autonegotiation for the suspect portAddresses Installation-Related IssuesPage General Specifications Appendix a Technical SpecificationsStandards Supported Data Rate and Encoding Environmental SpecificationsPerformance Specifications 64-byte packets Safety Agency ApprovalsPassport 8190SM Switch Management Module Management Port Connector Pin Number SignalConsole Serial Port Table A-3 DTE-to-DCE Pin Assignments Modem Serial PortPassport 8132TX Module Data Port ConnectorsConnector Type Cable Specifications450-1LR MDA, 450-1LX MDA Comm Port ConnectorMDAs 450-1SR MDA, 450-1SX MDAPassport 8148TX Module Port ConnectorsTable A-5. Passport 8148TX Port Pinouts GBICs Passport 8108GBIC Module1000BASE-SX Gbic Optical Specifications1000BASE-XD Gbic Figure A-1. MDI-X to MDI Cable Connections MDI and MDI-X ConnectionsFigure A-2. MDI-X to MDI-X Cable Connections Declaration of ConformityPage Figure B-1. LEDs on the Passport 8190SM Module Appendix B LEDsLabel Color/State Meaning Table B-1 LED Operation on the Passport 8190SM ModuleFigure B-2. LEDs on the Passport 8132TX and 8148TX Modules Passport 8132TX and 8148TX I/O ModulesColor/State Meaning LEDTable B-5 Port LEDs on the Passport 8108GBIC Module Page Appendix C Media Dependent Adapters Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Series MDAsLabel Type Color/State Meaning Table C-1 1000BASE-SX MDA LEDsTable C-2 1000BASE-LX MDA LEDs 8100-4TX MDATable C-3 8100-4TX MDA LEDs Series Fiber MDAsTable C-4 Series MDA LEDs Figure C-4 Series MDA Front PanelsFigure C-5. Installing an MDA Installing an MDAUsing the Passport 8100 Modules Figure D-1. Types of GBICs Appendix D Installing GBICsFigure D-2. Installing a Gbic Installing a GbicTo remove an installed Gbic Page Appendix E RFCs and Standards Page Numbers IndexIndex-2 Index-3 Index-4