Nortel Networks 8100, 1000BASE-XD manual Failure to Get a Login Prompt from the Console Port

Page 56

Using the Passport 8100 Modules

Failure to Get a Login Prompt from the Console Port

If you have connected a terminal to the Console port on the Passport 8190SM module and fail to get a login prompt, the port may have an incorrect DCE/DTE setting. Try moving the DCE/DTE switch from its current setting to the other position (Figure 4-1).

Console

DCEDTE

9595EA

Figure 4-1. DCE/DTE Switch on the Passport 8190SM Module

Failure of Management Software to Recognize I/O Modules

If management software does not recognize the presence of any I/O modules in the switch, the device view in Device Manager, for example, shows a switch with only a management module installed. This situation can occur when no I/O module is installed in slot 1 or slot 2 of the chassis. A Passport 8000 Series chassis must have an I/O module installed in slot 1 or slot 2 of the chassis to provide bus master functions for the switch.

LED Indications of Problems

If the switch is not operating properly, LEDs may provide information about the probable cause. Table 4-1 lists possible problems as indicated by LEDs on the switch modules and suggests corrective action.

4-2

204515-C

Image 56

Contents Using the Passport 8100 Modules EN 55 022 Statement EC Declaration of ConformityVoluntary Control Council for Interference Vcci Statement Bureau of Standards, Metrology and Inspection Bsmi Statement204515-C 204515-C 204515-C Contents Chapter Installing a Passport 8100 Module Appendix a Technical Specifications Appendix C Media Dependent Adapters Figures Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Tables Xiv Preface Before You BeginText Conventions Italic textRelated Publications Xviii How to Get Help Technical Solutions Center Telephone NumberPage Chapter About the Passport 8100 Modules Features About the Passport 8100 Modules Passport 8190SM Switch Management Module Passport 8190SM Management ModuleEthernet Management Port DTE/DCE Switch Reset ButtonSerial Ports Pcmcia Card SlotLEDs LEDs on the Passport 8190SM Module10BASE-T/100BASE-TX Port Connectors Passport 8132TX 32-Port I/O ModuleMDA Slot Comm PortLEDs on the Passport 8132TX Module Passport 8148TX Edge Switch Module Passport 8148TX 48-Port I/O ModulePassport 8108GBIC 8-Port I/O Module LEDs on the Passport 8148TX ModuleRedundancy Features Passport 8108GBIC ModuleRedundant Power Supplies Redundant Passport 8190SM ModulesPower Supply Hot-Swapping Chassis Number Hot-Swap One? Modules Power SuppliesCombining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Chassis Configuration Requirements Safety and Environmental PrecautionsInstalling a Module Removing a Filler PanelSlide the module into the slot Figure Turning On the Chassis Power Securing the Module in the ChassisConnecting Cables Replacing Modules Routing Network CablesTo replace a module Chapter Basic Switch Configuration Specifying Port Numbers Port Numbers on High-Density ModulesBooting the Switch Logging On to the System Access Levels and Default Login ValuesAccess Level Description Default Login Password Setting System Identification Assigning an IP Address to the Management PortSetting System Security Change CLI users and passwords using the following commandsChange Web passwords using the command Switch Configuration To assign an IP address for management, use the commandSpecify a default gateway address/default route Page Chapter Troubleshooting Normal Power-Up SequenceFailure of Management Software to Recognize I/O Modules Failure to Get a Login Prompt from the Console PortLED Indications of Problems LED Indications of Problems Symptom Probable Cause Corrective ActionPort Connection Problems CablingAutonegotiation Modes Use the CLI to disable autonegotiation for the suspect port Port InterfaceInstallation-Related Issues AddressesPage Standards Supported Appendix a Technical SpecificationsGeneral Specifications Environmental Specifications Performance Specifications 64-byte packetsSafety Agency Approvals Data Rate and EncodingPassport 8190SM Switch Management Module Console Serial Port Connector Pin Number SignalManagement Port Modem Serial Port Table A-3 DTE-to-DCE Pin AssignmentsData Port Connectors Connector TypeCable Specifications Passport 8132TX ModuleComm Port Connector MDAs450-1SR MDA, 450-1SX MDA 450-1LR MDA, 450-1LX MDATable A-5. Passport 8148TX Port Pinouts Port ConnectorsPassport 8148TX Module Passport 8108GBIC Module GBICsOptical Specifications 1000BASE-SX Gbic1000BASE-XD Gbic MDI and MDI-X Connections Figure A-1. MDI-X to MDI Cable ConnectionsDeclaration of Conformity Figure A-2. MDI-X to MDI-X Cable ConnectionsPage Appendix B LEDs Figure B-1. LEDs on the Passport 8190SM ModuleTable B-1 LED Operation on the Passport 8190SM Module Label Color/State MeaningPassport 8132TX and 8148TX I/O Modules Figure B-2. LEDs on the Passport 8132TX and 8148TX ModulesLED Color/State MeaningTable B-5 Port LEDs on the Passport 8108GBIC Module Page Appendix C Media Dependent Adapters Series MDAs Figure C-1 BASE-SX Shortwave Gigabit MDA Front PanelsTable C-1 1000BASE-SX MDA LEDs Label Type Color/State Meaning8100-4TX MDA Table C-2 1000BASE-LX MDA LEDsSeries Fiber MDAs Table C-3 8100-4TX MDA LEDsFigure C-4 Series MDA Front Panels Table C-4 Series MDA LEDsInstalling an MDA Figure C-5. Installing an MDAUsing the Passport 8100 Modules Appendix D Installing GBICs Figure D-1. Types of GBICsInstalling a Gbic Figure D-2. Installing a GbicTo remove an installed Gbic Page Appendix E RFCs and Standards Page Index NumbersIndex-2 Index-3 Index-4