Nortel Networks 8100 Chassis Configuration Requirements, Safety and Environmental Precautions

Page 38

Using the Passport 8100 Modules

Chassis Configuration Requirements

Slots in the Passport 8000 Series chassis are numbered from the top down, starting with 1. In either the Passport 8010 or the Passport 8006 chassis, slots 5 and 6 are reserved for the Passport 8190SM Switch Management Module. Any of the Passport 8100 Series I/O modules can be installed in the remaining chassis slots.

Note: You must install an I/O module in slot 1 or slot 2 to provide bus master functions in the switch.

Safety and Environmental Precautions

Before you perform any installation or replacement procedure on the switch, please note the following safe-handling guidelines:

•To prevent damage caused by electrostatic discharge (ESD), handle the switch chassis and modules only when you, the chassis, and the chassis modules are properly grounded. Nortel Networks recommends using a grounding wrist strap.

•When handling modules, do not touch components on the circuit boards; always handle modules by their edges. Store unused modules in their protective packaging.

•To maintain proper airflow and cooling, always cover unused module slots and power supply bays with filler panels.

2-2

204515-C

Image 38

Contents Using the Passport 8100 Modules EN 55 022 Statement EC Declaration of ConformityVoluntary Control Council for Interference Vcci Statement Bureau of Standards, Metrology and Inspection Bsmi Statement204515-C 204515-C 204515-C Contents Chapter Installing a Passport 8100 Module Appendix a Technical Specifications Appendix C Media Dependent Adapters Figures Figure C-1 BASE-SX Shortwave Gigabit MDA Front Panels Tables Xiv Preface Before You BeginText Conventions Italic textRelated Publications Xviii How to Get Help Technical Solutions Center Telephone NumberPage Chapter About the Passport 8100 Modules Features About the Passport 8100 Modules Passport 8190SM Switch Management Module Passport 8190SM Management ModuleEthernet Management Port Serial Ports DTE/DCE SwitchReset Button Pcmcia Card SlotLEDs LEDs on the Passport 8190SM Module10BASE-T/100BASE-TX Port Connectors Passport 8132TX 32-Port I/O ModuleMDA Slot Comm PortLEDs on the Passport 8132TX Module Passport 8148TX Edge Switch Module Passport 8148TX 48-Port I/O ModulePassport 8108GBIC 8-Port I/O Module LEDs on the Passport 8148TX ModuleRedundancy Features Passport 8108GBIC ModuleRedundant Power Supplies Redundant Passport 8190SM ModulesPower Supply Hot-Swapping Chassis Number Hot-Swap One? Modules Power SuppliesCombining Passport 8100 and Passport 8600 Modules Chapter Installing a Passport 8100 Module Chassis Configuration Requirements Safety and Environmental PrecautionsInstalling a Module Removing a Filler PanelSlide the module into the slot Figure Turning On the Chassis Power Securing the Module in the ChassisConnecting Cables Replacing Modules Routing Network CablesTo replace a module Chapter Basic Switch Configuration Specifying Port Numbers Port Numbers on High-Density ModulesBooting the Switch Logging On to the System Access Levels and Default Login ValuesAccess Level Description Default Login Password Setting System Identification Assigning an IP Address to the Management PortSetting System Security Change CLI users and passwords using the following commandsChange Web passwords using the command Switch Configuration To assign an IP address for management, use the commandSpecify a default gateway address/default route Page Chapter Troubleshooting Normal Power-Up SequenceFailure of Management Software to Recognize I/O Modules Failure to Get a Login Prompt from the Console PortLED Indications of Problems LED Indications of Problems Symptom Probable Cause Corrective ActionPort Connection Problems CablingAutonegotiation Modes Use the CLI to disable autonegotiation for the suspect port Port InterfaceInstallation-Related Issues AddressesPage Standards Supported Appendix a Technical SpecificationsGeneral Specifications Safety Agency Approvals Environmental SpecificationsPerformance Specifications 64-byte packets Data Rate and EncodingPassport 8190SM Switch Management Module Console Serial Port Connector Pin Number SignalManagement Port Modem Serial Port Table A-3 DTE-to-DCE Pin AssignmentsCable Specifications Data Port ConnectorsConnector Type Passport 8132TX Module450-1SR MDA, 450-1SX MDA Comm Port ConnectorMDAs 450-1LR MDA, 450-1LX MDATable A-5. Passport 8148TX Port Pinouts Port ConnectorsPassport 8148TX Module Passport 8108GBIC Module GBICsOptical Specifications 1000BASE-SX Gbic1000BASE-XD Gbic MDI and MDI-X Connections Figure A-1. MDI-X to MDI Cable ConnectionsDeclaration of Conformity Figure A-2. MDI-X to MDI-X Cable ConnectionsPage Appendix B LEDs Figure B-1. LEDs on the Passport 8190SM ModuleTable B-1 LED Operation on the Passport 8190SM Module Label Color/State MeaningPassport 8132TX and 8148TX I/O Modules Figure B-2. LEDs on the Passport 8132TX and 8148TX ModulesLED Color/State MeaningTable B-5 Port LEDs on the Passport 8108GBIC Module Page Appendix C Media Dependent Adapters Series MDAs Figure C-1 BASE-SX Shortwave Gigabit MDA Front PanelsTable C-1 1000BASE-SX MDA LEDs Label Type Color/State Meaning8100-4TX MDA Table C-2 1000BASE-LX MDA LEDsSeries Fiber MDAs Table C-3 8100-4TX MDA LEDsFigure C-4 Series MDA Front Panels Table C-4 Series MDA LEDsInstalling an MDA Figure C-5. Installing an MDAUsing the Passport 8100 Modules Appendix D Installing GBICs Figure D-1. Types of GBICsInstalling a Gbic Figure D-2. Installing a GbicTo remove an installed Gbic Page Appendix E RFCs and Standards Page Index NumbersIndex-2 Index-3 Index-4