Nortel Networks 5000BH manual Ffe

Page 38

Using the 8-port TokenSpeed and TokenSpeed/MCP Switch Modules

Table 3-3.

Factory default configuration settings (continued)

 

 

 

Parameter

Factory default

Possible settings

 

 

 

Filters

Disabled

Disabled, Enabled

Note: Do not enable both NetBIOS filtering and packet filtering on the same port. When both types of filtering are enabled, only the NetBIOS filtering is active.

Bridge group

1

1–32

Virtual ring number

For ports 1 through 8 on each slot in

1–FFE

(Valid only when source route

hexadecimal format:

 

bridging is selected.)

Slot 1: 11, 12, 13, 14, 15, 16, 17, 18

 

 

Slot 2: 21, 22, 23, 24, 25, 26, 27, 28

 

 

Slot 3: 31, 32, 33, 34, 35, 36, 37, 38

 

 

Slot 4: 41, 42, 43, 44, 45, 46, 47, 48

 

 

Slot 5: 51, 52, 53, 54, 55, 56, 57, 58

 

 

Slot 6: 61, 62, 63, 64, 65, 66, 67, 68

 

 

Note: The Centillion 50 switch contains only slots 1 through 3.

Priority

128

0–255

(Valid only when source route

 

 

bridging is selected.)

 

 

Path cost

16

1–65535

(Valid only when source route

 

 

bridging is selected.)

 

 

ARE hop count

7

1–7 or 1–13

(Valid only when source

 

 

route bridging is selected.)

 

 

STE hop count

7

1–7 or 1–13

(Valid only when source route

 

 

bridging is selected.)

 

 

SR broadcasting

Auto

Auto, Off, On

(Valid only when source route

 

 

bridging is selected.)

 

 

 

 

 

If the factory default settings are not appropriate for your network, you may be able to use one of the predefined switch configurations that are available in SpeedView. You simply choose one of these without having to configure individual ports.

3-10

893-01019-A

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Using the 8-port TokenSpeed TokenSpeed/MCP Switch Modules Trademarks Statement of ConditionsVoluntary Control Council for Interference Vcci Statement Iii893-01019-A 893-01019-A 893-01019-A Contents Chapter Installing and Connecting the TokenSpeed Module Figures Figure B -11. RI-other to RO connection RJ-45 to DB-9 Tables Xii Audience PrefacePurpose Special Message Formats Two-tiered Procedure FormatConventions Related publications Related PublicationsOrdering Bay Networks Publications Title DescriptionBay Networks Customer Support How to Get HelpTechnical Solutions Center Telephone number Fax number Region Telephone number Fax numberFor More Information 893-01019-A Chapter Overview of the TokenSpeed Module About the TokenSpeed ModuleFeatures TokenSpeed Module Ports and ConnectivityCaching and Proxy Fault ToleranceFiltering Network ManagementHardware features of the TokenSpeed module Physical DescriptionChapter TokenSpeed Module Applications Giving a Server a Dedicated PortSegmenting a Ring Giving a server a dedicated portConnecting a Segment Through the RI or RO Port Connecting a ring segment through an RI/RO port ring segmentConnecting a Segment Using a Lobe Port Connecting ring segments through lobe portsReplacing a Source Route Bridge or Router Concentrating Rings into a RouterConcentrating multiple rings into a router Installing and Connecting the TokenSpeed Module Preparing for InstallationInstalling the TokenSpeed Module Removing a filler panel Slot module guides Connecting Cables to TokenSpeed Ports Seating the moduleNetwork device port TokenSpeed port type Token Ring ConnectionsPort types for the TokenSpeed module Verifying the Installation Management ConnectionLED name Meaning LED Switch Startup SequenceTokenSpeed Module LEDs Configuring the TokenSpeed Module Factory default configuration settingsParameter Factory default Possible settings FFE Removing and Replacing a Module Replacing a TokenSpeed/MCP Module Loosening the TokenSpeed moduleSlide the module out of the chassis see Figure Replacing a TokenSpeed Module 11. Loosening the TokenSpeed module12. Removing the module from the Centillion chassis Page Troubleshooting the TokenSpeed Module Switch Startup Failure with TokenSpeed/MCP TokenSpeed Module Startup Failure Port Insertion Problems Verify that the cabling is correctTroubleshooting the TokenSpeed Module Page Appendix a Technical Specifications Environmental Specifications Safety Agency ApprovalsConnectors Electromagnetic EmissionsAppendix B Cables Table B-1 Port types for the TokenSpeed module Port TypesCable Types Cable type Mb/s 16 Mb/s UTP cable type Token Ring Connectors on the TokenSpeed ModuleTable B-2 Cable distances STP cable typeCable and Connector Pin Assignments Figure B-2. Connectors for token ring network cablesRJ-45 to RJ-45 Connection Figure B-3. Hub to station connection RJ-45 to RJ-45Figure B-4. Station to hub connection RJ-45 to RJ-45 Figure B-6. RI-other to RO connection RJ-45 to RJ-45 RJ-45 to DB-9 Connection Figure B-8. Hub to station connection RJ-45 to DB-9Figure B-9. Station to hub connection RJ-45 to DB-9 Figure B-11. RI-other to RO connection RJ-45 to DB-9 RJ-45 to IBM Type 1 Connection Figure B-13. Station to hub connection RJ-45 to IBM TypeFigure B-14. Bay/SNPX RO to RI connection RJ-45 to IBM Type Male Mini DIN 8 to male DB-25 cable Male Mini DIN Signal Male DB-25 Pin locations Pin numbersSerial MCP Connections Table B-3Request to send Clear to send Ring indicator Table B-4 Female DB-25 to female DB-9 adapterIndex Types, B-2 caching, RIFIndex-2 Index-3
Top Page Image Contents