Nortel Networks NN43001-318 manual

Page 2

Document status: Standard

Document version: 01.02

Document date: 20 June 2007

Sourced in Canada

The information in this document is subject to change without notice. The statements, conﬁgurations, technical data, and recommendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products speciﬁed in this document. The information in this document is proprietary to Nortel Networks.

Nortel, the Nortel Logo, the Globemark, SL-1, Meridian 1, and Succession are trademarks of Nortel Networks.

All other trademarks are the property of their respective owners.

Image 2

Contents

Isdn Basic Rate Interface Installation and Commissioning Page August JuneMay SeptemberRevision history Contents Generating trafﬁc reports Contents Contents About this document SubjectApplicable systems System migrationRelated information Intended audienceConventions TerminologyOnline CD-ROMContents Preparing the siteUnpacking and inspecting Taking inventoryInstalling Isdn BRI hardware Installing Isdn BRI hardware for line applicationsTo install Isdn BRI cards, perform the following steps Procedure Selecting the card slotsSILCs/UILCs MISPsBRSCs NT8D37 IPE module NT8D35 Network module Large SystemNT8D37 IPE module Large System NT4N41 Core/Network module Large SystemProcedure Remove the module cover for card installation Module cover locking latchesProcedure Installing the Misp Procedure Removing the MispProcedure Installing the BRSC, SILC, and Uilc Procedure Remove the BRSC, SILC, and Uilc Procedure Connecting Isdn BRI terminals to the systemStep Action End SILC/UILC port designations at the MDF Connect the system to the MDFInstalling Isdn BRI hardware for line applications Cross-connecting the MDF Step Action End Cross-connect the Silc port to the ofﬁce wiring Cross-connect the Uilc port to the ofﬁce wiring Silc Uilc Pairs Pair color PortPort signals Panel connectors Card Connecting the Isdn BRI terminals to the DSL Connecting the terminating resistors Procedure Connecting the Isdn BRI terminals to the DSLConnect the Isdn BRI terminal to the S/T interface Installing Isdn BRI hardware for trunk applications Installing the clock reference on the Silc Removing the module cover for card installationInstalling the Misp Procedure Providing clock referencing on the SilcConnecting clock reference cables Isdn BRI clock reference tables Code Length feet UseClock reference cable connection Clock recoveryProcedure Connecting clock reference cables Cross-connecting the Main Distribution Frame MDF Installing the Silc and the UilcConnecting the system to the Main Distribution Frame MDF Installing Isdn BRI hardware for trunk applications SILC/UILC or Brsc SILC/UILC or Brsc Number Slot number Connector PortsCard location forms Installing Isdn BRI hardware for trunk applications Installing Isdn BRI hardware Introduction Verifying Isdn BRI operationProcedure Performing acceptance testing Setting up Isdn BRI test terminals and trunksSet up Isdn BRI terminals Set up Isdn BRI trunking Local Exchange connectivity Isdn BRI acceptance testing setup for terminalsSet up Isdn BRI trunking TIE trunk connectivity Setting up Isdn BRI test terminals and trunks Preparing the system Hardware requirements Line and packet data applicationsIsdn BRI trunking Hardware Product code DescriptionNTAK20AB Correct responses to Loop and Misp prompts in LD Installation proceduresSummary Cabinet SystemsInstallation procedures Installation procedures Silc is not Silc is cloc See Note Clock reference ReferenceRemove the cover from the system 60 Conﬁguring Isdn BRI hardware Procedure Installing the SILCs and UILCs Remove the cover from the assigned systemSilc line power options Jumper plug settings for normal power on the TX and RX leads Procedure Removing the Silc and Uilc Procedure Installing the PRI hardwareConnecting the Isdn BRI terminals for line applications 66 Conﬁguring Isdn BRI hardware End 68 Conﬁguring Isdn BRI hardware Installation procedures Uilc port designation label at the cross-connect terminal TX+ BL-W BK-G TX+ BK-BR Cross-connecting a Silc port to the ofﬁce wiring 74 Conﬁguring Isdn BRI hardware Interface connector speciﬁcation RJ45 jack Pin signal name Signal name76 Conﬁguring Isdn BRI hardware End Connecting the Isdn BRI terminal to the S/T interface Connecting the Isdn network terminator to the U interface Procedure Initializing a Nortel Networks M5317TDX terminal M5317TDX terminal error codes Error Code Number Description No valid voice SpidConnecting the Isdn BRI trunks for trunking applications Error Code Number DescriptionEnd Cross-connecting an Silc port Cross-connecting a Uilc port 86 Conﬁguring Isdn BRI hardware Testing Isdn BRI functions Call Hold Procedure Performing a call hold testVoice calls Procedure Perform a Call Waiting test Call WaitingFeature Fundamentals NN43001-580 Call Forward No AnswerProcedure Performing a Call Forward No Answer test Calling Line Identiﬁcation Presentation and RestrictionIsdn BRI Conference National ISDN-1 and Etsi Procedure Perform an Isdn BRI Conference test Procedure Perform a Call Join test on Conference Isdn BRI Special Hunting Procedure Perform a hunting test Isdn BRI National ISDN-1 Call Forward All Calls Isdn BRI Etsi Call Forwarding Unconditional Circuit-switched data calls Procedure Perform a circuit-switched data call testPacket data transmission Packet data transmission End Procedure Perform procedure to test an Isdn BRI trunk DSL Testing an Isdn BRI trunkRemoving the test setup Testing Isdn BRI functions Generating trafﬁc reports Option Meaning Network traffic reportNetwork trafﬁc report Page Isdn Basic Rate Interface Installation and Commissioning