APC 990-1378 manual Start-up and Shutdown Procedure, Start-up from Maintenance Bypass

Page 38

Start-up and Shutdown Procedure

6.0Start-up and Shutdown Procedure

6.1Start-up from Maintenance Bypass

This section contains instructions on how to start the UPS from maintenance bypass. The steps in this procedure apply to units with an APC-supplied Maintenance Bypass Panel.

1.Make sure that the following switches are in the following positions:

The UPS AC disconnect switch should be “OFF”. The UPS bypass switch should be on “LINE”.

The battery breaker should be “OFF”. (External battery units)

2.Switch the UPS AC disconnect switch “ON”. The UPS display should show “System type xxkVA xxxV”.

3.Within 20 seconds, the UPS display should show **Stand-by** and an audible alarm should sound.

4.If the unit has external batteries:

a.Ensure that the external battery breaker for the battery system is set to “OFF”.

b.Open the DC fuse holder (F001, F002, F003). For location of DC fuse holder, see Component Overview illustration.

c.Place the DC fuses in the fuse holder. Make sure that the red tab on the fuse faces the top of the fuse holder. Make sure that the fuse locking tabs are aligned in the slots on the fuse holder.

d.Using an open palm, close the fuse holder.

e.Turn the pre-charge/discharge switch to the “pre-charge” position and keep it this position until the LED turns off.

f.Switch the battery breaker “ON”.

5.Press the green “on” button located inside the front door of the UPS. The UPS display should show “Normal operation load power xx%”.

6.For internal battery units, put the DC fuses (F001, F002, F003) into the DC fuse holder.

7.Using an open palm, close the fuse holder.

8.Program the unit into static bypass operation:

a.Press to access the user parameters.

b.Press the or key until the display shows “Bypass operation: OFF”.

c. Press to turn static bypass operation on. The display should show “Bypass operation”.

9.Set the UPS bypass switch to “UPS”.

10.Program the unit to normal operation:

a.Press to access the user parameters.

b.Press the or key until the display shows “Bypass operation: ON”.

c. Press to turn static bypass operation off. The display should show “Normal operation load power xx%”.

990-1378

38

Installation Guide APC BC300 Series 10kW 208/450/480V UPS

Page 37 Page 39
Image 38
Page 37 Page 39
Contents APC BC300 Series 10kW 208/450/480V Installation Guide Copyright 2002 APC Denmark ApSThank You Installation Guide APC BC300 Series 10kW 208/450/480V UPSSafety Symbols used in this manual Contents Tools and Equipment Needed IntroductionIntroduction Insulated Tools and Other Equipment NeededReceiving, Unpacking and Moving to Site Please RecycleRequirements on Site InstallationInstallation Insulated and other tools required Installing the Conduit Connection KitUPS Footprint measurements in inches & mm Installing Conduit Box and Base Covers Conduit Connection Kit ContentsInstalling Pedestals Installing the Maintenance Bypass Panel and UPS SBP Electrical Schematic 208V SBP Electrical Schematic SBP Electromechanical 10kW 208V SBP Electromechanical 10kW Component Overview door open Component OverviewWire Terminals Wire TerminalsWiring Diagram for BC300 Utility inputSingle Line Diagram for BC300 Single Line Diagram for BC300Wiring Line Diagram for BC300 25A.T UPS Model Input Output Recom DC Voltage DC Current Mended MIBExternal Connection Board External Connection BoardCommunication Interface Board Option Communication Interface BoardSmart Slot and Connection of Triple Chassis Communication InterfaceProduct Description Safety WarningsAPC BC300 Triple Chassis Monitoring PortInstalling Management Cards Power InputInstalling Management Products To UPS PortPower Considerations Cascading setup of the APC BC300 Triple ChassisPowering the APC BC300 Triple Chassis Power AdaptersTroubleshooting Triple Chassis Power ConsiderationsDetermining Power Requirements Problem Possible Cause SolutionProduct Specifications Monitoring Port Pin Assignments Monitoring Port Pin Assignment Battery Installation Installation of External Batteries and Battery BreakerPower, Physical, and Environmental Specifications PhysicalBattery Installation Guidelines Do not connect the negative cables to the UPS yet Battery Replacement Initial Start-up and Phase Check Internal Batteries Initial Start-up and Phase CheckInitial Start-up and Phase Check Initial Start-up and Phase Check External Batteries DC FusesInitial Start-up and Phase Check Clearing the Events Log Clearing the Events LogStart-up from Maintenance Bypass Start-up and Shutdown ProcedureStart-up and Shutdown Procedure Shutdown Procedure If you have shut the loads down Move on to stepAPC BC300 Series 10kW Technical Data Technical SpecificationsTechnical Specifications Battery Specifications GeneralDimensions/Weight BC300 Series UPS 10kWAPC Corporate How to Contact APCHow to Contact APC Fairgrounds Road West Kingston, RIHow to Contact APC

990-1378 specifications

The APC 990-1378 is a high-performance power supply designed for environments where reliability and efficiency are paramount. As a part of APC's range of power protection solutions, this unit is specifically engineered to safeguard critical electronic devices and maintain consistent power delivery even under demanding conditions.

One of the main features of the APC 990-1378 is its robust battery backup system. This ensures that connected devices remain operational during power outages, providing peace of mind for businesses and individuals relying on constant power supply for applications such as networking, telecommunications, and computer systems. The unit is equipped with advanced battery management technology that extends battery life while optimizing energy consumption.

In terms of technologies, the APC 990-1378 incorporates sine wave output, which delivers clean and stable power suitable for sensitive electronic equipment. This feature is essential for preventing equipment damage caused by power surges or fluctuations. Moreover, the power supply comes with multiple outlets, allowing users to connect several devices simultaneously without compromising performance.

Another characteristic that sets the APC 990-1378 apart is its intelligent LCD display. This user-friendly interface provides real-time information on power consumption, battery status, and system health, allowing users to monitor performance easily. The display also features customizable settings, giving users the flexibility to adapt the unit to their specific needs.

The build quality of the APC 990-1378 is impressive, designed to endure both indoor and outdoor environments. Its rugged casing and efficient cooling system guarantee reliable operation in various conditions, making it suitable for different applications, from home offices to enterprise data centers. Additionally, the compact design of this power supply saves valuable space, an essential consideration for users with limited installation areas.

The APC 990-1378 is also compatible with various management software solutions that facilitate remote monitoring and control. This capability is particularly beneficial for IT administrators who need to manage multiple units across different locations efficiently.

In summary, the APC 990-1378 is a versatile and reliable power supply that prioritizes performance, safety, and user convenience. Its advanced features and technologies make it a valuable asset for anyone seeking reliable power protection solutions in today's increasingly tech-driven world.
Top Page Image Contents