3Com 5000 quick start Installation Precautions

Page 3

COREBUILDER® 5000 SWITCHMODULE QUICK START AND REFERENCE

3

For ease of reading and because the DMM and A/DMM are basically the same, the term DMM is used in this release note to refer to both modules.

CAUTION: Do not upgrade to any later version until instructed to do so in Step 5.

See the CoreBuilder 5000 Distributed Management Module User Guide, Chapter 11, for information about DMM downloading.

CAUTION: Do not install the new SwitchModules yet.

1Upgrade all DMMs in the hub to software Version v5.00.

2Download SwitchModule boot software Version v1.05 to all SwitchModules in your hub.

3Download ATM SwitchModule software Version v3.00 operational code to all ATM Backbone SwitchModules in the hub. The ATM SwitchModule model number is 3C96602M-MOD.

4Upgrade all DMMs in the hub to software Version v6.00.

5Install the new SwitchModule into your hub. (See Section 7.0, "Installing the SwitchModule".)

6Download the Version v3.00 software code to the new SwitchModule.

To use the Frame Tagging feature, you must upgrade all SwitchModules in the hub to software Version v3.00 or later.

3Download SwitchModule software Version v3.00 to all SwitchModules in your hub, even if they are already running Version v3.00.

4Download ATM Backbone SwitchModule software Version v2.05 boot code, and then Version v3.00 operational code to all ATM Backbone SwitchModules in your hub. The Model Number is 3C96602M-MOD.

5Upgrade all DMMs in your hub to software Version v6.00.

6Install the new SwitchModule into your hub. (See Section 7.0, "Installing the SwitchModule".)

7Download the Version v3.00 software code to the new SwitchModule.

To use the Frame Tagging feature, you must upgrade all SwitchModules in the hub to software Version v3.00 or later.

4.2Download Procedure for SwitchModules at Version v2.02 or Later and DMMs at Version v5.00 or Later

If your hub contains any SwitchModules that are at Version v2.02 or later, and DMMs at Version 5.00 or later, complete the following download procedure:

CAUTION: Do not install the new SwitchModules yet.

1Download SwitchModule boot software Version v1.05 to all SwitchModules in the hub.

2Download SwitchModule software Version v3.00 operational code to all SwitchModules in the hub.

5.0Installation Precautions

Electrostatic discharge (ESD) can damage static-sensitive devices on circuit modules. Follow these precautions:

Do not remove the SwitchModule from its antistatic bag until you are ready to inspect or to install it.

Handle the SwitchModule by the front panel only; do not hold it by the component board.

Use proper grounding techniques when you install the SwitchModule. These techniques include using a foot strap and a grounded mat, wearing a grounded static discharge wrist strap, or touching the metal rack or frame just before you handle the SwitchModule.

When you handle CoreBuilder 5000 SwitchModules, follow these precautions to avoid component damage:

Do not twist or force the SwitchModule into the hub when you insert it into the module guides.

Match the upper and lower module guides while you slide the SwitchModule into place.

Do not push the SwitchModule all the way into the hub until the SwitchModule ejectors (if any) are open.

WARNING: To ensure optical safety when you install 10BASE-FB/FL, FDDI, and 100BASE-FX SwitchModules, comply with the following precaution:

Although the data communication LEDs and Lasers used in this product meet the regulatory requirements for casual exposure to the eye, as with any source of bright light, it is advised that you do not look into the light source.

Image 3
Contents Tools Required Installation PrerequisitesLearning About SwitchModules IntroductionCrucial Download Procedure Backplane Type Hub Type Installation GuidelineSoftware Prerequisites Installation Precautions Installing the SwitchModule Unpacking Procedure+12 Watts= Remaining HubBasic Configuration Steps Default Configuration After InstallationEnabling Snmp Management Through the SwitchModule LAN NMS Creating an Additional Virtual BridgeFinding More Information Enabling Communication Between Virtual BridgesManagement Task User Guide Reference Ports Common Front Panel Features11.0 10BASE-T SwitchModule Front Panel Features Reset Button10BASE-T Port Status or Activity Indicates LED StateEthernet Backplane SwitchModule Front Panel Features 13.0 10BASE-FB/FL SwitchModule Front Panel Features Optical Bypass Connector Mixed Technology SwitchModule Front Panel FeaturesPort Status LED State Indicates Fddi SwitchModules Front Panel FeaturesState Fast Ethernet SwitchModule Front Panel FeaturesCoreBuilder 5000 SwitchModule 3Com Corporation Limited Warranty
Related manuals
Manual 24 pages 21.07 Kb Manual 72 pages 3.4 Kb