Canon 900D manual Cannot Print Properly from the Digital Camera, Try This

Page 47

Cannot Print Properly from the Digital Camera

Cannot Print Properly from the Digital Camera

The following messages may be displayed on the cameras or camcorders when images are printed directly. Take the appropriate action to correct the error.

This section describes errors that can occur when you connect a Canon “Bubble Jet Direct” compatible digital camera to the printer.

Notes z Images can be printed directly from a “PictBridge” or Canon “Bubble Jet Direct” compatible digital cameras and digital video camcorders connected to this printer.

zIf the connected digital camera or digital video camcorder is not supported by this printer, the Power lamp on the printer will flash nine times. If this happens, disconnect the connection cable and press the Resume button.

zIf the operation time or data transmission time is too long, a communication time error may occur and no more images can be printed. If this error occurs, disconnect the camera connection cable, press the Resume button and then connect the cable once again.

The digital camera should be turned on automatically. If not, turn it on manually.

zA low ink warning is not displayed on the digital camera.

zFor more details, also refer to the user’s manual for the digital camera or digital video camcorder.

Error message on camera	Try This

Printer in use	Images are printed from the computer.
	Wait until printing ends.

Printer warming up	Wait until warm-up ends.

No Paper	Load the paper in the printer and press the Resume button on the printer.

Paper Jam	Remove the jammed paper, load new media, and press the Resume button.

Printer cover open	Close the front cover.

No print head	The Power lamp on the printer flashes five times.
	No print head is installed. Install a print head according to the Easy Setup
	Instructions.
	When there is a print head installed, the print head is defective.
	Contact the Customer Care Center.

Waste tank full	The waste ink tank is nearly full.
	Press the Resume button on the printer to recover from the error. Contact the
	Customer Care Center as soon as possible.

Printer error	An error requiring servicing has occurred. (The Power lamp on the printer flashes
	alternately orange and green.)
	Turn off the printer, unplug the power cord from the power supply, plug the power
	cord back in, and then turn on the printer. If the same error occurs, contact the
	Customer Care Center.

46

Image 47

Contents Series Photo Printer Direct Printing Guide Printing Maintenance ContentsContents Printing Flow Using a Memory CardOperation Panel Names and Functions 2 Power Lamp5 Settings Button Operation Panel and Menu Display10 Photo Viewer Button 12 Cancel Button14 Indicator Lamp 9 ButtonsPrint all Head cleaningDeep cleaning Menu DisplaysStep 3 Insert the memory card Printing FlowStep 1 Turn on the Printer Step 2 Load the paper Step 4 Selecting the Print Mode Step 5 Change/Confirm Print Settings and Start PrintingChange the Settings Inserting a Memory Card Using a Memory CardMemory Cards Supported by this printer 1 Turn on the printer 2 Open the card slot cover 3 Install the memory card in the card slotRemoving a Memory Card Turn on the printer and Load the Paper 4 Confirm the settingsPrinting Photograph Printing an Image Displayed on the LCD6 Start printing 5 Change the settings1 Turn on the printer Loading Paper„ Print Media to Avoid „ Loading the Print MediaLoad Limit Mark 3 Preparing to Load Paper4 Loading the Paper Paper Size „ Media Types for Card Direct PrintingMedia Type Paper Rest Load1 Prepare to print Printing Images from a Memory CardSpecifying how many copies to print for each image „ Specifying the number of copies to print for each image4 Start printing „ Printing a specified area - Trimming3 Specify the number of copies to print 3 Finalize the trimmed area 1 Set the Trimming Mode2 Trimming and Rotating the Sections you wish to Print 3 Start printing Printing all imagesPrinting an Image List - Print Index z Postcard Specifying the layoutz Bordered z Borderless2 Using the buttons to specify the number of copies to print 3 Specify the layout4 Select the image to print 5 Start printing2 Set the DPOF mode Printing According to the Settings Made on the Camera - DPOF Printing1 Turn on the printer and load the paper Specifying the Paper and Optimizing Images „ Settings Menu Display1 Select an item to set „ How to Make Settings„ Other Setting Items 2 Finalize the Settings„ Print Quality „ Borderless PrintingBorderless „ DateMedia Types for Digital Camera Digital Camera SettingPrinting Photographs Directly from a Digital Camera 3 Connect the digital camera and the printer 4 Start printing using the print function of the digital cameraPrinting from a Digital Camera Ensure that the printer is turned on Load the paperz You can make the following prints directly from a digital camera Print quality setting Maintenance1 Display the image you want to print in the Replay mode 2 Press the SET button to display the Print menuEnsure that the printer and the computer are turned on Using Photo Viewer3 Choose print settings and start printing Other Useful FunctionsThe Photo Viewer is terminated in the following case 4 Exit the Photo ViewerNotes Changing the Display Mode The Read/write attribute setting window appears Setting up the Card Slot as the Memory Card Drive of the ComputerOpen the USB memory card setup window The USB Memory Card Settings window appearsStart the BJ Utility Turn on the printer Select Maintenance from the MenuChanging the Language Displayed 3 Select Contrast Adjusting Contrast of the LCD3 Select a language for display 3 Select Quiet mode Reducing the Sound of Printer OperationReplacing an Ink Tank Knowing When to Replace an Ink TankWhen Low Ink is Detected 2 Remove the empty ink tank 3 Prepare a replacement tankReplacing Ink Tanks 1 Ensure that the printer is on, and then open the front cover5 Close the front cover 4 Install the ink tankStep2 Printing MaintenanceWhen Printing Becomes Faint or Colors are Incorrect Step1Printing the nozzle check pattern Printing the Nozzle Check PatternExamining the Nozzle Check Pattern After print head cleaning finishes Print Head CleaningEnsure that the printer is on Print Head Cleaning Ensure that the printer is on Print Head Deep Cleaning Print Head Deep CleaningAlign the print head automatically Note When Automatic Print Head Aligning Cannot Execute CorrectlyAligning Print Head - Auto head align Try This TroubleshootingA Message is Displayed on the LCD MessageIf the Same Error Persists Note Adjusting the Print Head ManuallyNote If the printed surface is still scratched „ Printed Surface is ScratchedPossible Cause „ Cannot Print Properly from the Digital Camera Error Message An Error Message is Displayed While Using the Photo ViewerIndex 7, 8 Read/write modeRead-only mode SmartMedia Card