Canon IP4200, QY8-13A9-000 Upon contact with the film, After replacement Service test print

Page 18

Purge unit: QM2- 2208

Waste ink tube: QC1- 6458

Waste ink tube holder: QC1-6460

Platen unit

QM2-2202

PR lift shaft ass'y QL2-0936

CL input gear QC1-6213

Timing slit strip film

secure the waste ink tube to the waste ink tube holder.

- Upon contact with the film,

1.To protect the waste ink tube from being pinched when reassembling the printer unit chassis into the bottom case unit, tape the tube (at 2 locations).

[See 3-2. Special Notes on Repair Servicing, (3) Printer unit and bottom case unit assembly.]

After replacement:

1.Check the ink system function.

[See 3-3. Adjustment / Settings, (5) Service mode.]

At replacement:

1.Apply grease to the sliding portions.

[See 3.3. Adjustment / Settings, (2) Grease application.]

After replacement:

case unit, the tube conditions are not visible. For confirmation of the tube conditions, perform the manual purging 3 or 4 times, and confirm that no strange noise is heard.

-Service test print

-Service test print

-Service test print

QC1-6394

Timing slit disk film QC1-6229

Print head

QY6-0059

*1: General notes:

wipe the film with ethanol.

- Confirm no grease is on the

film. (Wipe off any grease

thoroughly with ethanol.)

- Do not bend the film

1.Perform the print head alignment in the user mode.

After replacement:

- Service test print

1.Perform the print head alignment in the user mode.

-Make sure that the flexible cables and wires in the harness are in the proper position and connected correctly. [See 3-2. Special Notes on Repair Servicing, (2) Flexible cable and harness wiring, connection, for details.]

-Protect the waste ink tube from being pinched when assembling the printer unit chassis into the bottom case unit.

Since the tube conditions after assembly are not visible, perform the manual purging 3 or 4 times to confirm that no strange noise is heard.

[See 3-2. Special Notes on Repair Servicing, (3) Printer unit and bottom case unit assembly, for details.]

-Do not drop the ferrite core, which may cause damage.

-Protect electrical parts from damage due to static electricity.

-Before removing a unit, after removing the power cord, allow the printer to sit for approx. 1 minute (for capacitor discharging to protect the logic board ass'y from damages).

-Do not touch the timing slit strip film and timing slit disk film. No grease or abrasion is allowed.

-Protect the units from soiled with ink.

-Protect the housing from scratches.

-Exercise caution with the red screws, as follows:

i.The red screws of the paper feed motor may be loosened only at replacement of the paper feed motor unit (DO NOT loosen them in other cases).

ii.DO NOT loosen the red screws on both sides of the main chassis, securing the carriage shaft positioning (they are not adjustable in servicing).

1-13

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Scope RevisionCopyright TrademarksManual Outline II. Table of Contents Part Maintenance AdjustmentPeriodic replacement parts Customer MaintenancePeriodic maintenance Replacement consumablesPrint head Product LifePrinter Ink tank target valuePart 1 1. Maintenance Special ToolsSerial Number Location List of Error Display / Indication Operator Call Errors by Alarm LED Blinking in OrangePage Paper Feed Motor QK1-1502 See -3. Adjustment / Settings, 5 Service mode, for details Troubleshooting by Symptom Printer no LED indicationsPage Part 1 2. List of Error Display / Indication After replacement At replacementRepair After replacement Service test print Upon contact with the filmPart 1 3. Repair Special Notes on Repair Servicing External cover removalFlexible cable and harness wiring, connection Printer unit and bottom case unit assembly To the top Adjustment / Settings Paper feed motor adjustmentGrease application Page Part 1 3. REPAIR, 3-3 1 to Waste ink counter setting User modeService mode Print samplePage Part 1 3. REPAIR, 3-3 3 to Service test print Verification ItemsEeprom information print Print sampleHdeeprom Printed itemsPrinter Transportation Part 1 4. Printer TransportationTechnical Reference NEW Technologies Cleaning Mode and Amount of INK Purged Part 2 2. Cleaning Mode and Amount of INK Purged Print Mode ResolutionNormal color printing Grayscale printing Part 2 3. Print Mode Borderless printing Duplex printing Camera Direct printingFAQ Problems Specific to the iP4200 and Corrective Actions Service SolutionCleaning by user TemporaryPage Page Page Part 2 4. FAQ Appendix Block Diagram Part 3 1. Block DiagramPixma iP4200 Connector Location and PIN Layout Logic Board AssyCN101 Not used CN201 Print head 1/2 Carriage unit CN202 Print head 2/2 Carriage unit CN303 DSC harness CN301 AC adapterCN302 USB I/F CN401 CR lift sensor harnessCN403 Operation panel assy CN404 PE sensor / LF encoder harnessCN408 Maincam / Cdrg Part 3 2. Connector Location and PIN Layout CN501 Motor multi harnessCarriage Board Print Head Connector Romsk Pixma iP4200 Specifications Pixma iP4000 Specifications Supported ink tanks
Related manuals
Manual 6 pages 57.09 Kb Manual 6 pages 50.69 Kb

QY8-13A9-000, IP4200 specifications

The Canon IP4200 is a versatile and reliable inkjet printer that has garnered attention for its excellent performance and user-friendly features. Targeted primarily at home and small office users, this printer combines functionality, quality, and affordability into one compact design.

One of the standout features of the IP4200 is its impressive print resolution. With a maximum resolution of 4800 x 1200 dpi, this printer is capable of producing high-quality prints that exhibit sharp details and vibrant colors. This makes it an excellent choice for printing photographs, as well as everyday documents.

The Canon IP4200 employs Canon's advanced FINE (Full-photolithography Inkjet Nozzle Engineering) technology, which allows for precise ink placement and excellent uniformity in print quality. This technology works in conjunction with Canon's dye-based and pigment-based inks to ensure that images are both bright and durable. The printer's five-color individual ink system enables users to replace only the color that runs out, which not only saves costs but also reduces waste.

The IP4200 supports various paper types and sizes, ranging from standard letter and legal sizes to photo paper and specialty media such as labels and envelopes. With a dedicated photo tray, users can easily switch between printing documents and photos without the hassle of changing paper.

Another key feature of the Canon IP4200 is its impressive speed. The printer can produce black-and-white prints at speeds of up to 25 pages per minute and color prints at approximately 17 pages per minute. This efficiency makes it suitable for users who require quick printing without compromising on quality.

In terms of connectivity, the IP4200 offers USB support for easy connection to computers. It is compatible with various operating systems, including Windows and Mac, ensuring versatility for different users. The printer's compact design allows it to fit seamlessly into any workspace, taking up minimal desk space.

Overall, the Canon IP4200 stands as a hallmark of reliability and performance in the consumer inkjet market. With its high-quality prints, advanced ink technology, and user-friendly features, it remains a popular choice for anyone looking to achieve professional results from the comfort of their home or small office. Its excellent balance of speed and quality, along with its economical ink usage, make it a valuable investment for those who frequently print documents and photos.
Top Page Image Contents