Siemens 4200 Series, 4100 Series manual Click Infinite Time, Click Save Settings

Page 31

Router User’s Guide

Configuring Network Settings

4.In End IP Range, enter the ending IP address of the range of addresses from which the DHCP server will lease to requesting DHCP clients.

This range definition should consider the following address restrictions:

The range of IP addresses may extend over only one IP subnet.

The maximum size of the address pool that may be managed by the DHCP server is 64. Therefore, the range of addresses must not exceed 64.

The range of IP addresses should not include any IP address maintained internally by your SpeedStream device for other purposes. This includes the device’s LAN-side static IP address, as well as the Default Router IP address, Primary or Secondary DNS IP addresses, and Primary or Secondary Relay IP addresses.

Commonly used non-Internet routed IP address ranges include:

10.0.0.0- 10.255.255.255

172.16.0.0- 172.31.255.255

192.168.0.0 - 192.168.255.255

5.In IP Netmask, enter the IP subnet mask that corresponds to the range of IP addresses defined above.

6.In Default Gateway, do one of the following:

Enter the IP address of a default gateway, or router, to be provided to DHCP clients.

Click Self to specify that the SpeedStream Router is to be used as the default gateway.

7.In DNS Server (primary), do one of the following:

Enter IP address of the primary Domain Name System (DNS) server to be provided to DHCP clients. A DNS server may be used by clients to resolve domain names to IP addresses.

Click Use WAN to specify that the address of the DNS server provided by your ISP is provided to DHCP clients on the LAN.

8.In Domain Name, optionally enter the DNS domain name for the DHCP server resident on your SpeedStream device. This value must be entered as an alpha-numeric string.

9.In Lease Time, do one of the following:

Enter the period of time an IP addresses leased from the DHCP server is valid. At the end of the lease period, the DHCP client will transmit a request to the server to extend the lease, at which time the server will extend the lease period of the IP address assigned to the client. If the lease period expires without the server receiving a request from the client to extend the lease, the server will assume the client’s connection no longer exists. The server will release the IP address assigned to the client and return the address back to the pool of available addresses. (If you select this option, you must specify a DNS Server.)

Click Infinite Time:

Leaves the lease time open-ended, preventing the server from releasing the IP address.

10.Click Save Settings.

28

Image 31
Contents Series 4100 SpeedStream→ Router User’s GuideSoftware License General Provisions Contents Level Snooze Admin UserInterface Map Reboot Update Dynamic DNSIntroduction Features of the SpeedStream RouterNetwork LAN Features Security FeaturesAdvanced Router Functions General Safety GuidelinesConfiguration & Management Minimum System RequirementsResidential Gateway Family User Guide Physical InstallationHardware Installation Basic Installation ProcedureIn-Line Filter Installing Line FiltersWall-Mount Filter Connect the DSL cable Connecting CablesConnect the power Connect the Ethernet cablesConnect the USB Cable Install USB Driver SoftwareCheck TCP/IP Protocol Settings Operating System ConfigurationChecking TCP/IP Settings Windows 9x/ME Checking TCP/IP Settings Windows Checking TCP/IP Settings Windows XP Ethernet Adaptor en0,en1,… if connecting via USB Checking TCP/IP Settings MAC OS 8.6 throughChecking TCP/IP Settings MAC OSX For Windows XP Internet Access ConfigurationClick Setup. This starts the New Connection Wizard For Windows 9x/2000Before Configuring the Router SpeedStream Router SetupDo not require admin login Connecting to the RouterRequire admin login to access entire Web site Require admin login to access configuration pagesSelecting PPP Connection PPP Login Home Window Add User Profiles Configuring User ProfilesDisable all Content Filtering Require admin login to access configuration pages Deleting User Profiles Editing User ProfilesWAN Interface Configuring ISP Connection SettingsHost Disable EnableDhcp Relay Click Infinite Time Click Save SettingsStatic Routes RFC2684 EnabledRIP Configuring Network SettingsRIP Routing Information Protocol Port Forwarding UPnP Universal Plug and Play Bridge Mode Server Ports Dynamic DNS Time Client Configuring Security FeaturesAdmin User Time Client Select Enable from Enable Time ClientNAT&NAPT Enabled NAT & Napt DisabledNAT Only Enabled Napt Only EnabledSnooze FirewallLevel Snooze Disable SnoozeEnable Snooze, and set the Snooze time interval to Reset the Snooze time interval toMake Settings Last for Disable DMZEnable DMZ with this Host IP address Make Settings PermanentFilter Rules This IP Address Any IP Address− Any Protocol − TCP Transmission Control Protocol Greater than or equal to AnyLess than or equal to Equal toIcmp Options Window Clone IP Filter Rules Log Same Source and Destination Address Select Enable Attack DetectionBroadcast Source Address Fragmented TCP Header LAN Source Address on LANInvalid IP Packet Fragment Fragmented TCP PacketStatus and Statistics Monitoring Router HealthSystem Log System SummaryATM Statistics Ethernet Statistics Diagnostics Interface Map ToolsReset to system defaults RebootRemote UpdateLocal Basic Troubleshooting Steps TroubleshootingInterpreting the LED Display Post Failure red pwr LED Resolving Specific IssuesContacting Technical Support Parameter Default Value Your Value Configuration Data SheetsAdministrative User Setup Parameter Default Value Your Value User Name Admin PasswordFirewall Custom IP Filter Configuration Router User’s Guide Configuration Data Sheets Parameter Default Value Your Value Firewall Level Parameter Default Value Your Value LevelParameter Default Value Firewall DMZParameter Default Value Your Value Port Forwarding PPP Login Static Route Parameter Default Value Your Value Log Capture LevelSystem Log UPnP Technical Specifications Routing Standards Compliance Security Application High Medium Low Napt Off Firewall Security LevelsProtocol Compliant Out Http Https Icmp Rtsp SIP Smtp Siemens Subscriber Networks

4100 Series, 4200 Series specifications

Siemens has established itself as a leader in industrial automation with its innovative series of simulators, notably the 4200 Series and 4100 Series. Both series are designed to enhance operational efficiency and provide robust solutions across various industries, including manufacturing, logistics, and process engineering.

The Siemens 4200 Series is particularly known for its advanced functionalities. One of its main features is the integration of state-of-the-art motion control technology, enabling precise handling of complex automated processes. This series incorporates real-time control capabilities, allowing users to respond rapidly to changing production demands. Additionally, the 4200 Series supports a flexible architecture, which can be customized based on specific operational requirements. This adaptability ensures that businesses can optimize their workflow without significant overhauls to existing systems.

On the other hand, the 4100 Series offers an impressive combination of versatility and efficiency. This series is engineered with a focus on cost-effectiveness, making it suitable for small to medium-sized enterprises. A notable feature of the 4100 Series is its user-friendly interface, which simplifies the programming and monitoring of automation processes. The series also boasts comprehensive diagnostics tools that aid in minimizing downtime through proactive maintenance. The 4100 Series is designed to streamline operations, offering users the ability to integrate seamlessly with existing Siemens components.

Both series utilize cutting-edge technologies such as IoT connectivity, allowing for real-time data exchange and analytics. This capability enhances decision-making processes, as businesses can monitor their production systems remotely and make adjustments based on live data. Furthermore, energy efficiency is a crucial characteristic of both the 4200 and 4100 Series, with features designed to reduce energy consumption and overall operational costs.

In conclusion, the Siemens 4200 and 4100 Series stand out for their innovative features, robust technologies, and adaptability to various industrial applications. They provide comprehensive solutions that empower businesses to enhance productivity, achieve greater efficiency, and adapt to the rapidly changing technological landscape. As industries continue to evolve, Siemens remains at the forefront, delivering automation solutions that meet contemporary needs while paving the way for future advancements.