Siemens CL-010-I manual When returning to Network window, click Close

Page 20

9.When returning to Network window, click Close.

9.When returning to Network window, click Close.

10.When prompted with Network Settings Change dialog box, click Yes to restart your computer.

Image 20

Contents This manual currently suits for CL-010/CL-010-I User’s ManualCL-010/CL-010-I ADSL2+ Router Safety Notes For Installation For Using For ServiceFCC FCC Class B Notice IC StatementICES-003 Class B Notice - Avis NMB-003, Classe B ADSL Router User ManualFeatures PrefaceATM Features ADSL ComplianceBridging Features Routing FeaturesSecurity Features Configuration and ManagementUnpacking Subscription for ADSL Service Page Chapter 1 Overview Physical OutlookLED Indicators Front PanelRear Panel 9 VAC9VAC EthernetChapter 2 System Requirement and Installation System RequirementChoosing a place for the ADSL Router ™ ™ ™ ™Connecting the ADSL Router Setting TCP/IP Chapter 3 ConfigurationFor Windows 7. On IP Address tab 8. When returning to Network window, click OK 9. Wait for Windows copying filesFor Windows ME For Windows NT 5. Click Yes to use DHCP 9. When returning to Network window, click Close Option 2 If you have TCP/IP Protocol, go to Step 4. Highlight Protocol and then click Add 5. Click Internet Protocol TCP/IP and then click OKFor Windows XP Panel and then click Network and Internet ConnectionsProperties Click Internet ProtocolTCP/IP and then click OKFor Windows Vista 9. Click Network and Internet 10. Select Network and Sharing CenterSelect Internet Protocol Version 4 TCP/IPv4 and press Properties 11. Click Manage Network Connection on the left side12. Right click Local Area Connection and select Properties Configure PC to get IP address from DHCP Chapter 3 Configuration When prompted with the message below, click Yes to continue Enable Obtain an IP address automatically and then click OKWindows Vista Renew IP Address on Client PC For Windows 98ME2. Select Run from the Start menu 3. Type cmd in the dialog box and the click OK1. From the Start menu, point to Programs, Accessories and then click Command Prompt For Windows Vista Page Chapter 3 Connecting and Accessing Internet Chapter 3Connecting and Accessing InternetPPP over ATM PPPoA Mode ConfigurationPPP over ATM DescriptionPrimary IP address192.168.1.1 Subnet Mask255.255.255.0 PPP over ATM PPPoA IP Extension Mode2. Go to Advanced - Internet - Connections. And click Add PPP over Ethernet PPPoE Mode PPP over EthernetPPP over Ethernet PPPoE IP Extension Mode Numbered IP over ATM IPoA WAN IP Address WAN Subnet Mask Primary DNS serverSecondary DNS server Primary IP Address Subnet mask Start IP Address End IP AddressIP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT Primary IP Address Subnet mask Start IP Address End IP Address Unnumbered IP over ATM IPoA Primary DNS server Secondary DNS serverChapter 3Accessing Internet Unnumbered IP over ATM IPoA+NAT Primary IP Address Subnet maskStart IP Address End IP Address Bridge Mode Chapter 4 Web Configuration Using Web-Based ManagerTo Have the New Settings Take Effect Outline of Web ManagerLanguage TitleQuick Start Quick SetupConnect to Internet Connection TypePage PPP over ATM/ PPP over Ethernet PPP Password PPP UsernameAlways On Dial on DemandStart IP Address End IP AddressLeased Time DHCP Server OffIP over ATM NoneWAN IP Address WAN Subnet MaskPrimary IP Address Subnet MaskSecondary IP Address Subnet MaskPlease wait for 2 minutes for restarting the router Bridging Primary IP Address Status OverviewADSL Line ADSL BER TestInternet Connection Traffic StatisticsDHCP Table Routing TablePage Advanced Setup Local Network- IP AddressLocal Network - DHCP Server Host NameRelay On Server and Relay OffChapter 5Connection Mode Internet-Connections Setting Service CategoryLocal Network - UPnP Adding a New OneChapter 5Connection Mode IGMP Proxy Enabled Internet-DNS ServerInternet-IGMP Proxy Internet ConnectionInternet - ADSL Settings Enable ADSL PortCapability Enabled IP Routing - Static RouteConfiguring Other Routers on Your LAN Gateway IP AddressRemove Static Route Local RouterEnabled IP Routing - Dynamic RoutingExample - Static Route For the Router’s Routing Tabledifferent interface. Otherwise, disable this function Click Apply to invoke the settings set hereVirtual Server-Port Forwarding IP Address seen by Internet Users Add New Port ForwardingPre-defined User definedFrom Internet Host IP Address Connecting to the Virtual ServersVirtual Server-Port Triggering Virtual Server - DMZ Host Password： Virtual Server - Dynamic DNSDynamic DNS： Internet Connection：Select the direction to filter packets FirewallFiltering by IP address Allow Traffic ProtocolSource/Destination IP address Port RangeQuality of Service Bridge QoSTraffic Class Name 802.1p PriorityIP type of Service IPQoSSource IP Address/ Subnet Mask Source PortPort Mapping Destination PortGroup Name Available InterfacesManagement DiagnosticsAdmin Account Remote AccessSelect the Internet Connection Web BrowserUpdate Configure System LogInterntet Time System LogViewing System Log View System Log buttonSNMP Setting Enable TRAP ServiceSNMP Agent Read CommunityReset Router Backup ConfigUpdate Firmware UPnP for XP http//192.168.1.1/index.htmlChapter 5Connection Mode Problems with WAN Chapter 5 TroubleshootingProblems with LAN Problems with Upgrading Chapter 6 Glossary ARP Address Resolution ProtocolDHCP Dynamic Host Configuration Protocol LAN Local Area Network & WAN Wide Area NetworkPrivate IP Address Public IP AddressPVC Permanent Virtual Circuit RIP Routing Information ProtocolPage Chapter 7 Glossary Appendix A Specifications Appendix A Specifications 4. Make sure that Request a certificate is selected, and click Next Appendix B Server Setup for 802.1x ClientGetting Client Certificate Appendix C WEEE - B2C Appendix C WEEE - B2C