Siemens CL-010-I manual Connection Mode

Page 67

Manual background

Chapter 5:Connection Mode

The new one will be shown on the dialog right away. That is, the specified address will be reserved and not be assigned by DHCP for other computer.

Image 67

Contents CL-010/CL-010-I ADSL2+ Router User’s ManualThis manual currently suits for CL-010/CL-010-I For Installation For Using For Service Safety NotesADSL Router User Manual FCC FCC Class B NoticeIC Statement ICES-003 Class B Notice - Avis NMB-003, Classe BADSL Compliance FeaturesPreface ATM FeaturesConfiguration and Management Bridging FeaturesRouting Features Security FeaturesUnpacking Subscription for ADSL Service Page Front Panel Chapter 1 OverviewPhysical Outlook LED IndicatorsEthernet Rear Panel9 VAC 9VAC™ ™ ™ ™ Chapter 2 System Requirement and InstallationSystem Requirement Choosing a place for the ADSL RouterConnecting the ADSL Router Chapter 3 Configuration Setting TCP/IPFor Windows 7. On IP Address tab 9. Wait for Windows copying files 8. When returning to Network window, click OKFor Windows ME For Windows NT 5. Click Yes to use DHCP 9. When returning to Network window, click Close Option 2 If you have TCP/IP Protocol, go to Step 5. Click Internet Protocol TCP/IP and then click OK 4. Highlight Protocol and then click AddClick Internet ProtocolTCP/IP and then click OK For Windows XPPanel and then click Network and Internet Connections Properties9. Click Network and Internet 10. Select Network and Sharing Center For Windows Vista12. Right click Local Area Connection and select Properties 11. Click Manage Network Connection on the left sideSelect Internet Protocol Version 4 TCP/IPv4 and press Properties Configure PC to get IP address from DHCP For Windows ME Enable Obtain an IP address automatically and then click OK When prompted with the message below, click Yes to continueWindows Vista For Windows 98ME Renew IP Address on Client PC3. Type cmd in the dialog box and the click OK 2. Select Run from the Start menu1. From the Start menu, point to Programs, Accessories and then click Command Prompt For Windows Vista Page Chapter 3Connecting and Accessing Internet Chapter 3 Connecting and Accessing InternetDescription PPP over ATM PPPoA ModeConfiguration PPP over ATM2. Go to Advanced - Internet - Connections. And click Add PPP over ATM PPPoA IP Extension ModePrimary IP address192.168.1.1 Subnet Mask255.255.255.0 PPP over Ethernet PPP over Ethernet PPPoE ModePPP over Ethernet PPPoE IP Extension Mode Primary IP Address Subnet mask Start IP Address End IP Address Numbered IP over ATM IPoAWAN IP Address WAN Subnet Mask Primary DNS server Secondary DNS serverIP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT Secondary IP Address Subnet mask Primary DNS server Secondary DNS server Unnumbered IP over ATM IPoAIP Address Subnet Mask Gateway Primary IP Address Subnet mask Unnumbered IP over ATM IPoA+NATStart IP Address End IP Address Bridge Mode Using Web-Based Manager Chapter 4 Web ConfigurationTitle To Have the New Settings Take EffectOutline of Web Manager LanguageConnection Type Quick StartQuick Setup Connect to InternetPage PPP over ATM/ PPP over Ethernet Dial on Demand PPP PasswordPPP Username Always OnDHCP Server Off Start IP AddressEnd IP Address Leased TimeWAN Subnet Mask IP over ATMNone WAN IP AddressSubnet Mask Primary IP AddressSubnet Mask Secondary IP AddressPlease wait for 2 minutes for restarting the router Bridging Start IP Address Overview StatusADSL BER Test ADSL LineRouting Table Internet ConnectionTraffic Statistics DHCP TablePage Host Name Advanced SetupLocal Network- IP Address Local Network - DHCP ServerServer and Relay Off Relay OnChapter 5Connection Mode Adding a New One Internet-Connections SettingService Category Local Network - UPnPChapter 5Connection Mode Internet Connection IGMP Proxy EnabledInternet-DNS Server Internet-IGMP ProxyIP Routing - Static Route Internet - ADSL SettingsEnable ADSL Port Capability EnabledLocal Router Configuring Other Routers on Your LANGateway IP Address Remove Static RouteFor the Router’s Routing Table EnabledIP Routing - Dynamic Routing Example - Static RouteClick Apply to invoke the settings set here different interface. Otherwise, disable this functionVirtual Server-Port Forwarding User defined IP Address seen by Internet UsersAdd New Port Forwarding Pre-definedVirtual Server-Port Triggering Connecting to the Virtual ServersFrom Internet Host IP Address Virtual Server - DMZ Host Internet Connection： Password：Virtual Server - Dynamic DNS Dynamic DNS：Filtering by IP address FirewallSelect the direction to filter packets Port Range Allow TrafficProtocol Source/Destination IP address802.1p Priority Quality of ServiceBridge QoS Traffic Class NameSource Port IP type of ServiceIPQoS Source IP Address/ Subnet MaskDestination Port Port MappingAvailable Interfaces Group NameDiagnostics ManagementWeb Browser Admin AccountRemote Access Select the Internet ConnectionSystem Log UpdateConfigure System Log Interntet TimeView System Log button Viewing System LogRead Community SNMP SettingEnable TRAP Service SNMP AgentUpdate Firmware Backup ConfigReset Router http//192.168.1.1/index.html UPnP for XPChapter 5Connection Mode Problems with LAN Chapter 5 TroubleshootingProblems with WAN Problems with Upgrading LAN Local Area Network & WAN Wide Area Network Chapter 6 GlossaryARP Address Resolution Protocol DHCP Dynamic Host Configuration ProtocolRIP Routing Information Protocol Private IP AddressPublic IP Address PVC Permanent Virtual CircuitPage Chapter 7 Glossary Appendix A Specifications Appendix A Specifications Getting Client Certificate Appendix B Server Setup for 802.1x Client4. Make sure that Request a certificate is selected, and click Next Appendix C WEEE - B2C Appendix C WEEE - B2C