Siemens CL-010-I manual Highlight Protocol and then click Add

Page 22

4.Highlight Protocol and then click Add.

4.Highlight Protocol and then click Add.

5.Click Internet Protocol (TCP/IP) and then click OK.

6.When returning to Local Area Connection Properties window, highlight Internet Protocol (TCP/IP) and then click Properties.

7.Under the General tab, enable Use the following IP Address. Enter the IP address: 192.168.1.x (x is between 2 and 254), Subnet Mask: 255.255.255.0 and Default gateway: 192.168.1.1. Then click OK.

Image 22

Contents CL-010/CL-010-I ADSL2+ Router User’s ManualThis manual currently suits for CL-010/CL-010-I Safety Notes For Installation For Using For ServiceICES-003 Class B Notice - Avis NMB-003, Classe B FCC FCC Class B NoticeIC Statement ADSL Router User ManualATM Features FeaturesPreface ADSL ComplianceSecurity Features Bridging FeaturesRouting Features Configuration and ManagementUnpacking Subscription for ADSL Service Page LED Indicators Chapter 1 OverviewPhysical Outlook Front Panel9VAC Rear Panel9 VAC EthernetChoosing a place for the ADSL Router Chapter 2 System Requirement and InstallationSystem Requirement ™ ™ ™ ™Connecting the ADSL Router Setting TCP/IP Chapter 3 ConfigurationFor Windows 7. On IP Address tab 8. When returning to Network window, click OK 9. Wait for Windows copying filesFor Windows ME For Windows NT 5. Click Yes to use DHCP 9. When returning to Network window, click Close Option 2 If you have TCP/IP Protocol, go to Step 4. Highlight Protocol and then click Add 5. Click Internet Protocol TCP/IP and then click OKProperties For Windows XPPanel and then click Network and Internet Connections Click Internet ProtocolTCP/IP and then click OKFor Windows Vista 9. Click Network and Internet 10. Select Network and Sharing Center12. Right click Local Area Connection and select Properties 11. Click Manage Network Connection on the left sideSelect Internet Protocol Version 4 TCP/IPv4 and press Properties Configure PC to get IP address from DHCP Chapter 3 Configuration When prompted with the message below, click Yes to continue Enable Obtain an IP address automatically and then click OKWindows Vista Renew IP Address on Client PC For Windows 98ME2. Select Run from the Start menu 3. Type cmd in the dialog box and the click OK1. From the Start menu, point to Programs, Accessories and then click Command Prompt For Windows Vista Page Chapter 3 Connecting and Accessing Internet Chapter 3Connecting and Accessing InternetPPP over ATM PPP over ATM PPPoA ModeConfiguration Description2. Go to Advanced - Internet - Connections. And click Add PPP over ATM PPPoA IP Extension ModePrimary IP address192.168.1.1 Subnet Mask255.255.255.0 PPP over Ethernet PPPoE Mode PPP over EthernetPPP over Ethernet PPPoE IP Extension Mode Secondary DNS server Numbered IP over ATM IPoAWAN IP Address WAN Subnet Mask Primary DNS server Primary IP Address Subnet mask Start IP Address End IP AddressIP Address Subnet Mask Gateway Numbered IP over ATM IPoA+NAT Primary IP Address Subnet mask Start IP Address End IP Address Unnumbered IP over ATM IPoA Primary DNS server Secondary DNS serverChapter 3Accessing Internet Unnumbered IP over ATM IPoA+NAT Primary IP Address Subnet maskStart IP Address End IP Address Bridge Mode Chapter 4 Web Configuration Using Web-Based ManagerLanguage To Have the New Settings Take EffectOutline of Web Manager TitleConnect to Internet Quick StartQuick Setup Connection TypePage PPP over ATM/ PPP over Ethernet Always On PPP PasswordPPP Username Dial on DemandLeased Time Start IP AddressEnd IP Address DHCP Server OffWAN IP Address IP over ATMNone WAN Subnet MaskSecondary IP Address Primary IP AddressSubnet Mask Subnet MaskPlease wait for 2 minutes for restarting the router Bridging DHCP Server On Status OverviewADSL Line ADSL BER TestDHCP Table Internet ConnectionTraffic Statistics Routing TablePage Local Network - DHCP Server Advanced SetupLocal Network- IP Address Host NameRelay On Server and Relay OffChapter 5Connection Mode Local Network - UPnP Internet-Connections SettingService Category Adding a New OneChapter 5Connection Mode Internet-IGMP Proxy IGMP Proxy EnabledInternet-DNS Server Internet ConnectionCapability Enabled Internet - ADSL SettingsEnable ADSL Port IP Routing - Static RouteRemove Static Route Configuring Other Routers on Your LANGateway IP Address Local RouterExample - Static Route EnabledIP Routing - Dynamic Routing For the Router’s Routing Tabledifferent interface. Otherwise, disable this function Click Apply to invoke the settings set hereVirtual Server-Port Forwarding Pre-defined IP Address seen by Internet UsersAdd New Port Forwarding User definedVirtual Server-Port Triggering Connecting to the Virtual ServersFrom Internet Host IP Address Virtual Server - DMZ Host Dynamic DNS： Password：Virtual Server - Dynamic DNS Internet Connection：Filtering by IP address FirewallSelect the direction to filter packets Source/Destination IP address Allow TrafficProtocol Port RangeTraffic Class Name Quality of ServiceBridge QoS 802.1p PrioritySource IP Address/ Subnet Mask IP type of ServiceIPQoS Source PortPort Mapping Destination PortGroup Name Available InterfacesManagement DiagnosticsSelect the Internet Connection Admin AccountRemote Access Web BrowserInterntet Time UpdateConfigure System Log System LogViewing System Log View System Log buttonSNMP Agent SNMP SettingEnable TRAP Service Read CommunityUpdate Firmware Backup ConfigReset Router UPnP for XP http//192.168.1.1/index.htmlChapter 5Connection Mode Problems with LAN Chapter 5 TroubleshootingProblems with WAN Problems with Upgrading DHCP Dynamic Host Configuration Protocol Chapter 6 GlossaryARP Address Resolution Protocol LAN Local Area Network & WAN Wide Area NetworkPVC Permanent Virtual Circuit Private IP AddressPublic IP Address RIP Routing Information ProtocolPage Chapter 7 Glossary Appendix A Specifications Appendix A Specifications Getting Client Certificate Appendix B Server Setup for 802.1x Client4. Make sure that Request a certificate is selected, and click Next Appendix C WEEE - B2C Appendix C WEEE - B2C