Monitor Audio EN 55013 Installation In-Wall Units, To FINE-TUNE the Speakers Please Refer to

Page 6

Installation - In-Wall Units

The CP Series In-Wallloudspeakers will provide long term satisfaction in terms of sound quality and reliability provided they are installed correctly, according to the instructions and conditions contained in this manual. Please read this installation guide carefully before proceeding. We assume the installer is trained and skilled in the correct and safe use of hand and power tools, and has a working knowledge of local building and fire regulations/codes as well as experience of the conditions/services behind walls and ceilings into which these speakers will be installed. IF IN DOUBT ABOUT YOUR ABILITY TO INSTALL THESE PRODUCTS SAFELY AND

CORRECTLY PLEASE CONTACT YOUR LOCAL AUTHORISED MONITOR AUDIO DEALER OR CUSTOM INSTALLER.

Parts List

PLEASE CHECK YOU HAVE THE FOLLOWING ITEMS IN THIS KIT BEFORE PROCEEDING:

1 x Complete speaker & tweeter assembly fitted to back box.

1 x Grille (which can be painted).

1 x Mounting cut out template (in packaging).

2 x Grille membrane (one for use during painting and the other as a clean replacement).

2 x Spare baffle mounting screws plus guarantee card in this manual.

WARNINGS:

A minimum depth of 98mm (4 Inches) is required for the back box to fit into wall/ceiling recess.

The fixing clamps require a minimum of 25mm (1 Inch) of surface area around the cut-out hole to ensure a secure fixing!

The fixing clamps will operate on walls with a minimum thickness of 9mm (3/8 Inches) to a maximum depth of 32mm (1¼ Inches).

Do not attempt to fix these speakers to your wall if you are unsure of your ability to provide a secure and safe fixing. IF IN DOUBT CONTACT YOUR LOCAL AUTHORISED MONITOR AUDIO DEALER.

Ensure that there are no water pipes, air ducts or electricity cables running immediately behind the cut out area!

Please work from secure steps or scaffold and avoid trailing wires for your safety and those around you.

Always turn off the amplifier or other devices in the system when connecting these speakers.

Procedure

1.Secure template in position. Please note that the outer profile indicates size of cut-out. Fig 3. The adhesive backing allows for repositioning a number of times.

2.Cut hole and Locate speaker cable and connect as shown below Fig 4.

3.Fit back box into prepared hole and tighten fixing clamps. These will move outwards on tightening! DO

NOT OVERTIGHTEN! Once contact is made 2-3 turns are all that is required.

4.Paint at a time to suit. Use paint masks (membrane) supplied and replace with new item supplied.

5.TO FINE-TUNE THE SPEAKERS PLEASE REFER TO PAGE 6.

In-wall template

 

 

Push down to fit cable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hole size to be cut

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

387 x 234mm

Red (Positive)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(15 1/4” x 9 3/16” )

 

 

 

 

 

 

 

Black (Negative)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Position of 8 fixing clamps

Not to scale

Fig 3

Fig 4

6

Image 6
Contents Contents Dealer or Custom InstallerFine tuning & Calibration IntroductionSpeaker Location Gold CP Features Silver CP FeaturesBronze CP Features Procedure Installation In-Ceiling UnitsParts List To FINE-TUNE the Speakers Please Refer to page 4Gold CP Silver CP Bronze CP Fine-tuning the loudspeakersSpecifications In-Ceiling In-CeilingInstallation In-Wall Units To FINE-TUNE the Speakers Please Refer toAdjusting M.F Mid-range Frequency control Fine-tuning In-Ceiling and In-wall speakersAdjusting H.F High Frequency control Silver CP and Gold CP models onlyIn-Wall Guarantee and Service Claims under this GuaranteeWarnungshinweis AttenzioneAdvertencias Avertissements