Toshiba TDP-P75 Indicator lights, When the projector is in a normal state, State Remark

Page 40

English

Indicator lights

The front of the projector has three lights that indicate its status. Check the following for information about the indicator lights. If an abnormal condition is indicated, turn off the projector and contact your dealer.

When the projector is in a normal state:

POWER

TEMP

LAMP

State

Remark

 

 

 

 

 

Orange

Off

Off

Standby mode

---

 

 

 

 

 

Flashing

Off

Off

The projector is powering

Cannot turn off the

Green

up.

projector.

 

 

 

 

 

 

 

Green

Off

Off

The projector is under

---

normal operation.

 

 

 

 

 

 

 

 

 

Flashing

Off

Off

The projector needs to cool

Cannot turn on the

Orange

down for 90 seconds after

projector.

 

 

the power is turned off.

 

 

 

 

 

 

 

 

 

When the projector is in an abnormal state:

POWER

TEMP

LAMP

State

 

Remark

 

 

 

 

 

Off

Off

Red

The lamp has exceeded its

Solution:

usage life.

Install a new lamp.

 

 

 

 

 

 

 

 

Red

Red

Off

 

Solution:

 

 

 

 

Make sure the ventilation

Red

Red

Green

 

 

 

 

 

 

holes are not blocked.

Red

Red

Red

 

 

The internal temperature is

Relocate the projector.

 

 

 

Off

Red

Off

too high.

Stop using the projector

Off

Red

Green

• The intake ventilation or

 

until the ambient

 

 

 

the exhaust ventilation is

 

temperature falls within

Green

Red

Off

 

blocked.

 

the specified range. The

 

 

 

 

 

 

 

 

 

 

 

• The projector may be in a

 

maximum operating

 

 

 

poorly ventilated location.

 

temperature is specified

 

 

 

• The ambient temperature

 

as 35°C (95°F).

Green

Red

Green

may be too high.

• Make sure the power

The fans are not working.

 

supply is stable.

 

 

 

 

 

 

 

 

Check if there is an

 

 

 

 

 

obeject stuck in the fans.

 

 

 

 

Contact your dealer.

 

 

 

 

 

 

40 Additional Information

Image 40
Contents TDP-P75 Safety Precaution Model Name TDP-P75USA only Canada only Important Safety Instructions Power sourcesSource of light HeatPower cord protection CleaningVentilation Water and moistureAccessories Lightning stormsDo not place the product vertically Do not stack componentsDamage requiring service Replacement partsSafety check ServicingDo not use the product in a closed installation state Power Supply Cord SelectionFor long periods of time Important Precautions Save Original Packing MaterialsExemption Clauses Other Notes and Information CopyrightsRemote Control Batteries Notational Conventions Used in This ManualContents Additional Information Troubleshooting SpecificationsRegulation statements Shipping contents OverviewProjector exterior view Front / Upper sideRear side Bottom sideControls and functions Control panelRemote Control Front Rear Remote controlName Main Function Preparing and using the remote control Loading dry-cell batteries into the remote controlOperating the remote control Remote controlSwitching operation modes Connecting a computer Operating a computer using the remote controlOperating a computer Positioning your projector Choosing a locationFloor front II. Ceiling frontConnection Projection distance and sizeScreen As seen from above Min length =Connecting to a Component Video device Connecting to a computer480i 480p 576i 576p 720p 50/ 60 Hz 1080i 50/ 60 Hz Connecting Video and S-Video devices Video or Video devices Video cable or Audio cableOperation Start upAdjusting the image Adjusting the heightAuto-adjusting the image Fine-tuning the image size and claritySwitching input signals Adjusting the volumeCorrecting keystone For exampleShutdown Functions available when receiving different Signal typesMenu operation Menu systemImage adjustment and press 5 or 6 button to select Keystone Using the menusMenu. Refer to p.34 for more details Image adjustment menu Display setting menu Default setting menu Information menu Cleaning the lens Cleaning the projector caseAdditional Information Care of the projectorReplace the lamp when a sign appears on the screen When the lamp is brokenAbout the lamp Storing the projectorLamp warning message Replacing the lampDo not turn the power on with the lamp cover removed Indicator lights When the projector is in a normal stateWhen the projector is in an abnormal state State RemarkTroubleshooting Specifications Projector specificationsDimensions Signal timingSupported signal format for Component-YPBPRInput Supported timing for PC inputSupported signals for Video and S-Video inputs Regulation statements FCC statementEEC statement MIC statement