Toshiba TLP650U, TDP-ET20, TLP671U, TLP651U, TLP651A, TLP650A, TLP670U Remote control operation

Page 15

Before use

(Continued)

Notes

Using batteries incorrectly can cause them to leak or burst. Strictly observe the following.

•Install the batteries with their + and – ends facing correctly.

•Do not charge, heat, disassemble, or short the batteries or throw them into a fire.

•Do not leave exhausted batteries in the remote control.

•Do not mix different types of batteries or new and old batteries.

•When you will not be using the remote control for a prolonged period, take the batteries out of the remote control.

•When the remote control stops working or only works from very close distance, replace all the batteries with new ones.

•When replacing the batteries, use a more longer life alkaline batteries.

•If a battery leaks, carefully wipe off any residue inside the battery case before loading new batteries.

Remote control operation

Point the remote control at the infrared remote sensor and press a button.

Front side

Rear side

15° 15°

15° 15°

Rear side (document imaging camera model)

15° 15°

CONTENTS

15

Notes

•Do not leave the remote control unit turned the face down as it may make the buttons pressed to hasten the battery end.

•The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor.

•Operate the remote control from a position where the remote sensor is visible.

•Do not drop the remote control or otherwise jolt it.

•Keep the remote control out of locations with excessively high temperature or humidity.

•Do not get water on the remote control or place wet objects on it.

•Do not disassemble the remote control.

•Under unusual circumstances the remote control may not operate well due to the location being used or the surroundings. At such times, change the direction of the remote control to the projector and retry the operation.

Distance : within about 5 meters from the front of the remote sensor.

Angle : within about 15° of the remote sensor in every direction.

Image 15

Contents 3LCD Data Projector Safety Precautions Important Precautions Power Sources Source of LightVentilation Water and Moisture Power-Cord Protection Heat Cleaning OverloadingStack Inhibited AccessoriesObject and Liquid Entry Do not place the product verticallyReplacement Parts Damage Requiring Service ServicingDo not move the projector while the arm is still erect Do not carry by the camera armPower supply cord selection Before use ContentsMain unit Part names and functionsTo connect a computer to control the projector RGB Input connectors RGB input, Audio inputLeft side Right side Rear sidePOINTER/PJ selector Remote controlAuto SET button 10 2 Keystone buttonInstalling batteries Remote control operation Connecting an IBM PC or compatible computer DOS/V Connecting a Macintosh computerConnections Output terminals Connecting video equipmentPreparation Projector placementTake off the lens cover Connect the power cordTurn the foot adjuster to make fine adjustment of the height How to use the foot adjusterPicture projection Press Keystone Turning the power offPress ON/STANDBY after using the projector Correcting the keystone distortionDisplaying the input source Information Adjusting the image automaticallyFreezing the picture Cutting off the picture and sound TemporarilyPress Resize Changing the picture sizeConnecting the Remote Mouse Receiver Operating the computer By the remote controlTo left-click Operating the computer by Remote controlTo drag and drop To move the pointerAudio33 Settings and adjustments on MenuKeystone30 Image31Initial settings Default Menu disappears Press MenuPress Enter Keystone correctionPress Menu to display the menu To select Press to select Auto setMenu Press or to select Projection adjustments ImagePress or to select a preferred item To adjust Press Menu to displayPress To select a Preferred item Picture adjustmentsSound adjustments Audio Press To select a Preferred item To adjustMenu Press To select Press Enter Press Menu Saving data SavePart names and functions Document imaging camera Preparation of the document imaging Camera Turn the armPull up the light Picture projection with Document imaging camera Arm Mode of the documentWhen finished, turn off Press PHOTO/TEXT to selectPrepare a white paper to write on Press Overlay Project the paper using the cameraOverlaying projection Write on the paper with a blue or red penLamp Temp Trouble indicationsReplacing the intake, exhaust fans Air filter Air filter, lens and main unit CleaningCleaning the lens Cleaning the main unit Cleaning the air filterLoad a new lamp Lamp replacementReset the lamp timer Pull out the lampBefore calling service Personnel Others Mode determination and signal system Input SignalXGA60 Signal assignment Input SignalPin arrangements Timing chart RGB signal defaultsInterface format Adjustments with RS-232COthers Document imaging camera SpecificationsLiquid crystal display Projection lensAccessories Your Responsibility Limited two 2 Years Warranty of Parts and LaborStep-by-step procedure how to obtain warranty service Toshiba TLP600/400 Series 3LCD Data ProjectorOthers