Toshiba TLP671U Projection adjustments Image, Press Menu to display, Menu Press or to select

Page 31

Adjustments

Projection adjustments

– Image

Preparation

•Display the image as explained in “Picture Projection”. 21

•Set the POINTER/PJ selector to “PJ”.

SELECT/ADJUST

ON

ON/STANDBY MENU

ENTER

INPUT

LAMP

TEMP

	AUTO SET	ON/STANDBY	AUTO SET
	KEYSTONE		AUTO SET
	MARKER	LASER	2,3,5,6
1,7	PJ		2,3,5,6
	POINTER

4

L-CLICKR-CLICK

MENU ENTER

RGB VIDEO CAMERA

RESIZE RESET FREEZE

RESET

1	Press MENU to display the
	menu.

2	Press or to select
			.
			.

I ma g e

A u t o s y n c .
P h a s e	–				+

H – p o s i t i o n	–				+

V – p o s i t i o n	–				+

C l o c k	–				+

3 Press to select “Auto sync.”

4 Press ENTER.

The image is automatically adjusted. For further adjustments, follow the below steps.

5 Press or to select a preferred item.

6 Press or	to adjust the
item.
To select another item, go back to step 5.
Phase:	To reduce flickers.
H-position:	To shift the image to the
	left (–), to the right (+).
V-position:	To shift the image down (–),
	to up (+).
Clock	To remove vertical stripes.

7 Press MENU.
The menu disappears.

CONTENTS

31

Notes

•When performing the automatic projection adjustment, use a bright and distinctly edged picture.

•Pressing AUTO SET on the remote control can also adjust the image automatically. 23

•If you project an image from a computer with an LCD screen while monitoring the image on the computer, the image may not be projected properly, depending on the computer model. In this case, turn off the computer display, or make the necessary picture adjustments on the projector. For details on controlling the computer display, etc., refer to the computer’s manual and description on the software for the computer used.

•During adjustments of “H-position” or “V- position”, the image may not be projected properly.

•While using, an aberration of the phase may occur. In that case, adjust “Phase” again.

•Some item may be displayed in gray depending on an input source. The item displayed in gray cannot be adjusted and/or set.

•These adjustments are stored until you turn the power off.

•To store the adjustments even if the power is

turned off, follow the procedure of “Saving data”. 34

•Pressing RESET will return the adjustment or setting currently selected to default.

Image 31

Contents 3LCD Data Projector Safety Precautions Important Precautions Source of Light Power SourcesVentilation Water and Moisture Power-Cord Protection Heat Cleaning OverloadingStack Inhibited AccessoriesObject and Liquid Entry Do not place the product verticallyReplacement Parts Damage Requiring Service ServicingDo not move the projector while the arm is still erect Do not carry by the camera armPower supply cord selection Before use ContentsMain unit Part names and functionsTo connect a computer to control the projector RGB Input connectors RGB input, Audio inputLeft side Right side Rear sidePOINTER/PJ selector Remote controlAuto SET button 10 2 Keystone buttonInstalling batteries Remote control operation Connecting a Macintosh computer Connecting an IBM PC or compatible computer DOS/VConnections Output terminals Connecting video equipmentPreparation Projector placementTake off the lens cover Connect the power cordTurn the foot adjuster to make fine adjustment of the height How to use the foot adjusterPicture projection Press Keystone Turning the power offPress ON/STANDBY after using the projector Correcting the keystone distortionDisplaying the input source Information Adjusting the image automaticallyFreezing the picture Cutting off the picture and sound TemporarilyPress Resize Changing the picture sizeConnecting the Remote Mouse Receiver Operating the computer By the remote controlTo left-click Operating the computer by Remote controlTo drag and drop To move the pointerAudio33 Settings and adjustments on MenuKeystone30 Image31Initial settings Default Menu disappears Press MenuPress Enter Keystone correctionPress Menu to display the menu To select Press to select Auto setMenu Press or to select Projection adjustments ImagePress or to select a preferred item To adjust Press Menu to displayPress To select a Preferred item Picture adjustmentsPress To select a Preferred item To adjust Sound adjustments AudioMenu Press To select Press Enter Press Menu Saving data SavePart names and functions Document imaging camera Turn the arm Preparation of the document imaging CameraPull up the light Picture projection with Document imaging camera Arm Mode of the documentWhen finished, turn off Press PHOTO/TEXT to selectPrepare a white paper to write on Press Overlay Project the paper using the cameraOverlaying projection Write on the paper with a blue or red penLamp Temp Trouble indicationsReplacing the intake, exhaust fans Air filter Air filter, lens and main unit CleaningCleaning the lens Cleaning the main unit Cleaning the air filterLoad a new lamp Lamp replacementReset the lamp timer Pull out the lampBefore calling service Personnel Others Mode determination and signal system Input SignalXGA60 Input Signal Signal assignmentPin arrangements Timing chart RGB signal defaultsInterface format Adjustments with RS-232COthers Document imaging camera SpecificationsLiquid crystal display Projection lensAccessories Your Responsibility Limited two 2 Years Warranty of Parts and LaborStep-by-step procedure how to obtain warranty service Toshiba TLP600/400 Series 3LCD Data ProjectorOthers