Toshiba TDP-ET20 Keystone correction, Press Menu to display the menu To select, Press Enter

Page 30

Adjustments

Keystone correction

– Keystone

Preparation

•Display the image as explained in “Picture Projection”. 21

•Set the POINTER/PJ selector to “PJ”.

SELECT/ADJUST

ON

ON/STANDBY MENU

ENTER

INPUT

LAMP

TEMP

	AUTO SET	ON/STANDBY
	KEYSTONE
		KEYSTONE
	MARKER	LASER
1,7	PJ	2,3,5,6
	POINTER

4

L-CLICKR-CLICK

MENU ENTER

RGB VIDEO CAMERA

RESIZE RESET FREEZE

RESET

1 Press MENU to display the menu.

2 Press

or

to select

.

Ke y s t o n e

A u t o s e t
A d j u s t	–	+

3	Press to select “Auto set”.

4	Press ENTER.

The keystone distortion is corrected automatically. For further correction, follow the below steps.

5 Press .

6	Press or to correct the
	distortion.
	(–): To reduce the upper width.
	(+): To reduce the lower width.

7	Press MENU.
	The menu disappears.

CONTENTS

30

Notes

•Pressing KEYSTONE on the remote control

can also correct the keystone distortion automatically. 22

•These adjustments are stored until you turn the power off.

•Pressing RESET will return the adjustment or setting currently selected to default.

•Pictures may be slightly deteriorated by the keystone correction.

0 degrees setting for the automatic

keystone correction

Depending on the operating condition such as vibration, the distortion may be beyond the automatic keystone correction. The horizontal condition setting (0 degrees setting) may be disordered. In such a case, perform the following 0 degrees setting to correct the distortion.

1)Place the projector on a level surface.

2)On the menu, select “Auto set” in “Keystone”.

3)Press RESET.

Notes

•Do not make the 0 degrees setting on an inclined or unstable surface or in a shaky place as it may not be performed properly.

•To store this setting even if the power is

turned off, follow the procedure of “Saving data”. 34

Image 30

Contents 3LCD Data Projector Safety Precautions Important Precautions Power Sources Source of LightVentilation Heat Cleaning Overloading Water and Moisture Power-Cord ProtectionDo not place the product vertically AccessoriesObject and Liquid Entry Stack InhibitedDamage Requiring Service Servicing Replacement PartsDo not carry by the camera arm Do not move the projector while the arm is still erectPower supply cord selection Contents Before usePart names and functions Main unitRear side RGB Input connectors RGB input, Audio inputLeft side Right side To connect a computer to control the projector10 2 Keystone button Remote controlAuto SET button POINTER/PJ selectorInstalling batteries Remote control operation Connecting an IBM PC or compatible computer DOS/V Connecting a Macintosh computerConnections Connecting video equipment Output terminalsProjector placement PreparationConnect the power cord Take off the lens coverHow to use the foot adjuster Turn the foot adjuster to make fine adjustment of the heightPicture projection Correcting the keystone distortion Turning the power offPress ON/STANDBY after using the projector Press KeystoneCutting off the picture and sound Temporarily Adjusting the image automaticallyFreezing the picture Displaying the input source InformationChanging the picture size Press ResizeOperating the computer By the remote control Connecting the Remote Mouse ReceiverTo move the pointer Operating the computer by Remote controlTo drag and drop To left-clickImage31 Settings and adjustments on MenuKeystone30 Audio33Initial settings Default Press Menu Menu disappearsPress to select Auto set Keystone correctionPress Menu to display the menu To select Press EnterPress Menu to display Projection adjustments ImagePress or to select a preferred item To adjust Menu Press or to selectPicture adjustments Press To select a Preferred itemSound adjustments Audio Press To select a Preferred item To adjustMenu Press To select Saving data Save Press Enter Press MenuPart names and functions Document imaging camera Preparation of the document imaging Camera Turn the armPull up the light Picture projection with Document imaging camera Press PHOTO/TEXT to select Mode of the documentWhen finished, turn off ArmWrite on the paper with a blue or red pen Project the paper using the cameraOverlaying projection Prepare a white paper to write on Press OverlayTrouble indications Lamp TempCleaning the main unit Cleaning the air filter Air filter, lens and main unit CleaningCleaning the lens Replacing the intake, exhaust fans Air filterPull out the lamp Lamp replacementReset the lamp timer Load a new lampBefore calling service Personnel Others Input Signal Mode determination and signal systemXGA60 Signal assignment Input SignalPin arrangements RGB signal defaults Timing chartAdjustments with RS-232C Interface formatOthers Projection lens SpecificationsLiquid crystal display Document imaging cameraAccessories Toshiba TLP600/400 Series 3LCD Data Projector Limited two 2 Years Warranty of Parts and LaborStep-by-step procedure how to obtain warranty service Your ResponsibilityOthers