Toshiba TLP-T50M Important Precautions Avoid Volatile Liquid, LCD Panel, Moisture Condensation

Page 5

POWER SUPPLY CORD SELECTION

If your line voltage is 220 to 240V, use one of the following types of cable.

IMPORTANT PRECAUTIONS (Continued)

Avoid Volatile Liquid

Plug

Line voltage

configuration Plug type

EURO

220 – 240V

UK

220 – 240V

Use a 5A fuse which is approved by ASTA or BSI to BSI362.

Always replace the fuse cover after changing the fuse.

Plug

 

configuration Plug type

Line voltage

Australian

200 – 240V

240V

 

10A

 

Switzerland

200 – 240V

240V

 

6A

 

North American

200 – 240V

240V

 

15A

 

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time. They will leave marks on the finish.

If cleaning with a chemically saturated cloth, be sure to follow the product's precautions.

LCD Panel

The life of the LCD panel is limited. Take care over the points below so as to use the panel for years.

To prolong the life of this panel, never fail to turn the power off when the panel is not in use

and make sure that the lamp has gone out. The state of the lamp being extinguished helps

enhance the effect of energy saving.

If the air filter is stained and is clogged up, the main unit inner temperature rises. As a

result, the life of the LCD is shortened and a malfunction may also occur.

Clean the air filter from time to time and replace it regularly. It is recommended that this

replacement be done at the time of replacing a lamp. (Ask a dealer where the unit was

Before Using

IMPORTANT PRECAUTIONS

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to ship your LCD projector. For maximum protection, repack the set as it was originally packed at the factory.

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location. When the unit is exposed to such a change in temperature, moisture may condense on the crucial internal parts. To prevent the unit from possible damage, do not use the unit for at least 2 hours when there is an extreme or sudden change in temperature.

Place and Manner of Installation

Do not place in hot locations, such as near heating equipment. Doing so could cause malfunction, and shorten the life of the LCD panel.

Avoid locations with oil or cigarette smoke. Doing so will dirty the LCD panel and other optical parts, shortening their lives, and darkening the screen.

Do not use in angle of 20° or more degrees. Doing so could shorten the life of the lamp.

If used at high altitudes, the unit could cease operation even if used within the rated temperature range. This is because the thinner air at high altitudes decreases the internal cooling efficiency. Therefore, please lower the ambient temperature if using at high altitudes.

purchased or your nearby service station about an air filter for replacement.)

In the spaces provided below, record the Model and Serial No. located at the bottom of your LCD projector.

Model No.

Serial No.

Retain this information for future reference.

8

9

Image 5
Contents TLP-T50MXGA / with a mouse remote control Others Maintenance Operations Preparations Before UsingVentilation Power SourcesSource of Light Important Safety Instructions Damage Requiring Service Before UsingReplacement Parts Safety CheckPlace and Manner of Installation Important Precautions Avoid Volatile LiquidLCD Panel Save Original Packing MaterialsExemption Clauses Names of each part on the main unit Checking the package contentsControl panel Remote ControlNames of the connection terminals Loading dry-cell batteries into the remote control Preparing and using the remote control PlacementPlacement Styles Projection Distance and Screen SizeOperations Turning the power on and offConnection Basic operations Basic operations Using handy featuresCutting off the picture and sound temporarily Mute Using handy featuresEnlarging the picture size Resize Displaying Information Status display Using the menusHow to use the menus Image adjustment menu Using the menuDefault setting menu Display setting menuLens and main unit cleaning Air filter cleaningLamp replacement MaintenanceOthers Lamp replacementTrouble indications List of general specifications Before calling service personnelSpecifications List of supported signals RGB signals SpecificationsList of supported signals Y/PB/PR signals List of supported signals Video, S-Video signalsControl terminal Main CommandsSeparately Sold Product Pin assignment