Toshiba TLP-MT7E manual Power Sources, Source of Light, Ventilation

Page 4

4

IMPORTANT SAFETY INSTRUCTIONS

Before use

CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit will protect you if you observe the following procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1.Read Owner’s Manual

After unpacking this product, read the owner’s manual carefully, and follow all the operating and other instructions.

2.Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company.

For products intended to operate from battery power, or other sources, refer to the operating instructions.

3.Source of Light

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight.

4.Ventilation

Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

Continued

Image 4
Contents TLP-MT7E Safety Precautions Avoid Volatile Liquid Save Original Packing MaterialsMoisture Condensation Source of Light Power SourcesVentilation Important Safety Instructions Heat Cleaning OverloadingPower-Cord Protection Water and MoistureAccessories Object and Liquid EntryDo not place the product vertically Stack InhibitedDamage Requiring Service Replacement PartsSafety Check ServicingPlug Configuration Plug type Line voltage Power supply cord selection220 Contents Names of each part on the main unit Lamp indicator 25 28 Temp indicator 64 Busy indicator Selection buttonExit button Menu buttonControl connector 24 RS-232C connector Component in connector 21Video connector Audio in jack Audio input 21 23 ø 3.5mm stereo mini-jackNames of each part on the remote control Install the batteries Loading batteriesOpen the cover Attach the coverRemote control operation Floor-mounted projector placement ViewerFloor-mounted projector placement Contents Power cord Supplied Connect the power cordTake off the lens cover Obtained and hold down the foot adjuster release button Turn clockwise to lift up Turn counterclockwise to lowerCeiling-mounted projector placement Ceiling-mounted rear projectionConnecting video equipment Video equipment DVD player, etcConnecting video equipment Connecting a computer Connection Installationand Projector operation control by a computerPlayback mode Projection on the screenPress ON/STANDBY Turn on the connected equipment and put itSignal sent from the computer Select the input sourcePress the Input button repeatedly to select it Icon of the input source selected appearsAdjust the picture size by turning Focusing ringPress VOL/ADJ +/ to adjust volume Zooming leverPress ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Remote control Control panel Correcting the keystone distortionPress Auto Keystone Main unit sideRemote control Icon appears in the resize modeEnlarging the picture size Press ResizeIcon Appears in the mute mode Cutting off the picture and sound temporarilyPress Mute Sound and picture are cut off temporarilyAppears in the freeze mode Freezing the picturePress Freeze Picture freezesAdjusting the picture automatically Computer input Input full screen video signals from the inputSource computer and project the image Press Auto SETDisplaying PIP Sub-pictures Press PIPSub-picture is displayed Press the PIP button again to turn off the sub-pictureDisplaying Information Press CallInput Lamp timeAdjustments and settings on the menu screen Quick MenuOperating the menu screen Quick Menu adjustments and settings You can set the basic setting used frequentlyPress Menu Quick Menu appearsSettings Press VOL/ADJ +/ to adjust and set Remote control Main unit sideSub-menu screen of input source setting appears Press EnterPress VOL/ADJ +/- to select the type of input source Press Exit to return to the Quick MenuUse the selection buttons / to select a language Finished, press Exit After the adjustments and settings areMenu screen disappears Press Menu twice Full Menu adjustments and settings PictureUse the selection buttons / to select Signal format Video mode YesFrequency Adjust vertical stripes Adjust vertical stripes Yes Settable No Not displayedScreen size Computer input Screen size Video input, S-Video input, Y/PB/PR inputPress Exit to return to the Full Menu Sub-menu of selected items appears PositionLevelUse the selection buttons / to select setting items Signal format Y/PB/PR inputVideo mode Video input, S-Video input Sub-menu of selected items appearsEnter Full Menu settings Audio Use the selection buttons To select Setting itemsUse the selection button To display Audio menu To move back to itAfter the settings are finished, press Exit When set to Off, no sound is produced from the speakersSpeaker output Channel selectFull Menu settings Keystone Use the selection buttons To display Keystone menuSub-menu of Horizontal reference value reset appears Horizontal reference value is resetedYes and press Enter KeystoneWhen pressed once, the Quick Menu screen appears. When Full Menu settings DisplayUse the selection buttons To display Display menu Sub-menu of Language appears Portuguê s PortugueseMenu position No signal background Setting of screen of no signal inputStart-up screen Full Menu settings Default setting Use the selection buttons To display Default setting menuWhen pressed once, the Quick Menu screen appears. When Pressed twice, the Picture screen of the Full Menu appearsSub-menu of Input source setting appears VideoUse the selection buttons / to select the projection mode Sub-menu of Projection mode appearsRear ceiling Ceiling-mounted front projectionPower on No signal power offPress VOL/ADJ +/ to set Factory default setting Full Menu settings Factory reset modePicture menus for the each input to Menu screen disappears Setting items, then press VOL/ADJ +/ to set PIP menu settingMenu screen disappears Indicator Trouble indicationsAir filter cleaning Unplug the power cordClean the air filter Take off the air filter coverMount the air filter cover Assemble the air filterAir filter Filter frame Air filter cover Lens and main unit cleaning Cleaning the lensCleaning the main unit Replacing the intake, exhaust fans and air filterLamp replacement Wait until the lamp gets cold enoughTake off the lamp cover on Bottom panelReset the lamp timer Load a new lampAttach the lamp cover Slide the cover in place and tighten two screwsBefore calling service personal Before calling service personal Mini D-sub 15pin connector Do not connect anythingTiming chart Mode Resolution Clock Pixels KHz MHz LinesMode Fh kHz Fv Hz Fsc MHz 15.73 480i 59.9415.63 480p 31.47 59.94 15.63 25 or 720p 45.00 60.00Pin No Signal Description Method Signal groundItems/Status Selection Adjustment Computer Video/S-Video Command PowerComputer Video/S-Video Command Picture Position Picture mode BrightPicture mode Standard Video mode AutoComputer Video/S-Video Command Audio Speaker output Horizontal reference value resetNo signal background Logo OffComputer Video/S-Video Command Display Default Input source setting SettingProjection mode Standard No signal power off OffComputer Video/S-Video Command Volume Increase Enlargement resetDecrease Input select ToggleSpecifications Replacement lamp