Toshiba TLP-MT7E manual Lens and main unit cleaning, Cleaning the lens, Cleaning the main unit

Page 67

Lens and main unit cleaning

67

CAUTION

If you use the projector mounted on the ceiling, ask the dealer to carry out the maintenance such as cleaning.

Cleaning the lens

• Use a blower or a lens cleaner to clean the lens.

• Never rub or tap the lens with a hard object as the lens surface is fragile.

Cleaning the main unit

Pull out the power cord before cleaning.

Use a soft cloth to wipe off stains from the

surface.

• To remove difficult stains, use a soft cloth slightly moistened with a weak solution of synthetic detergent and water, and finish with a soft, dry cloth.

Replacing the intake, exhaust fans and air filter

To maintain the efficiency of the projector, replace the intake and exhaust fans about every two to three years.

Ask the dealer for the replacement.

Maintenance

Image 67
Contents TLP-MT7E Safety Precautions Avoid Volatile Liquid Save Original Packing MaterialsMoisture Condensation Source of Light Power SourcesVentilation Water and Moisture Important Safety InstructionsHeat Cleaning Overloading Power-Cord ProtectionStack Inhibited AccessoriesObject and Liquid Entry Do not place the product verticallyServicing Damage Requiring ServiceReplacement Parts Safety CheckPlug Configuration Plug type Line voltage Power supply cord selection220 Contents Names of each part on the main unit Menu button Lamp indicator 25 28 Temp indicator 64 Busy indicatorSelection button Exit buttonAudio in jack Audio input 21 23 ø 3.5mm stereo mini-jack Control connector 24 RS-232C connectorComponent in connector 21 Video connectorNames of each part on the remote control Attach the cover Install the batteriesLoading batteries Open the coverRemote control operation Viewer Floor-mounted projector placementFloor-mounted projector placement Contents Power cord Supplied Connect the power cordTake off the lens cover Turn clockwise to lift up Turn counterclockwise to lower Obtained and hold down the foot adjuster release buttonCeiling-mounted rear projection Ceiling-mounted projector placementVideo equipment DVD player, etc Connecting video equipmentConnecting video equipment Connecting a computer Projector operation control by a computer Connection InstallationandTurn on the connected equipment and put it Playback modeProjection on the screen Press ON/STANDBYIcon of the input source selected appears Signal sent from the computerSelect the input source Press the Input button repeatedly to select itZooming lever Adjust the picture size by turningFocusing ring Press VOL/ADJ +/ to adjust volumePress ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Main unit side Remote control Control panelCorrecting the keystone distortion Press Auto KeystonePress Resize Remote controlIcon appears in the resize mode Enlarging the picture sizeSound and picture are cut off temporarily Icon Appears in the mute modeCutting off the picture and sound temporarily Press MutePicture freezes Appears in the freeze modeFreezing the picture Press FreezePress Auto SET Adjusting the picture automatically Computer inputInput full screen video signals from the input Source computer and project the imagePress the PIP button again to turn off the sub-picture Displaying PIP Sub-picturesPress PIP Sub-picture is displayedLamp time Displaying InformationPress Call InputQuick Menu Adjustments and settings on the menu screenOperating the menu screen Quick Menu appears Quick Menu adjustments and settingsYou can set the basic setting used frequently Press MenuSettings Remote control Main unit side Press VOL/ADJ +/ to adjust and setPress Exit to return to the Quick Menu Sub-menu screen of input source setting appearsPress Enter Press VOL/ADJ +/- to select the type of input sourceUse the selection buttons / to select a language Finished, press Exit After the adjustments and settings areMenu screen disappears Press Menu twice Full Menu adjustments and settings PictureUse the selection buttons / to select Yes Settable No Not displayed Signal formatVideo mode Yes Frequency Adjust vertical stripes Adjust vertical stripesScreen size Video input, S-Video input, Y/PB/PR input Screen size Computer inputSub-menu of selected items appears PositionLevel Press Exit to return to the Full MenuSub-menu of selected items appears Use the selection buttons / to select setting itemsSignal format Y/PB/PR input Video mode Video input, S-Video inputEnter To move back to it Full Menu settings AudioUse the selection buttons To select Setting items Use the selection button To display Audio menuChannel select After the settings are finished, press ExitWhen set to Off, no sound is produced from the speakers Speaker outputUse the selection buttons To display Keystone menu Full Menu settings KeystoneKeystone Sub-menu of Horizontal reference value reset appearsHorizontal reference value is reseted Yes and press EnterWhen pressed once, the Quick Menu screen appears. When Full Menu settings DisplayUse the selection buttons To display Display menu Portuguê s Portuguese Sub-menu of Language appearsMenu position No signal background Setting of screen of no signal inputStart-up screen Pressed twice, the Picture screen of the Full Menu appears Full Menu settings Default settingUse the selection buttons To display Default setting menu When pressed once, the Quick Menu screen appears. WhenVideo Sub-menu of Input source setting appearsCeiling-mounted front projection Use the selection buttons / to select the projection modeSub-menu of Projection mode appears Rear ceilingPower on No signal power offPress VOL/ADJ +/ to set Factory default setting Full Menu settings Factory reset modePicture menus for the each input to Menu screen disappears Setting items, then press VOL/ADJ +/ to set PIP menu settingMenu screen disappears Trouble indications IndicatorTake off the air filter cover Air filter cleaningUnplug the power cord Clean the air filterMount the air filter cover Assemble the air filterAir filter Filter frame Air filter cover Replacing the intake, exhaust fans and air filter Lens and main unit cleaningCleaning the lens Cleaning the main unitBottom panel Lamp replacementWait until the lamp gets cold enough Take off the lamp cover onSlide the cover in place and tighten two screws Reset the lamp timerLoad a new lamp Attach the lamp coverBefore calling service personal Before calling service personal Do not connect anything Mini D-sub 15pin connectorMode Resolution Clock Pixels KHz MHz Lines Timing chart15.63 25 or 720p 45.00 60.00 Mode Fh kHz Fv Hz Fsc MHz15.73 480i 59.94 15.63 480p 31.47 59.94Computer Video/S-Video Command Power Pin No Signal Description MethodSignal ground Items/Status Selection AdjustmentVideo mode Auto Computer Video/S-Video Command Picture PositionPicture mode Bright Picture mode StandardOff Computer Video/S-Video Command Audio Speaker outputHorizontal reference value reset No signal background LogoNo signal power off Off Computer Video/S-Video Command DisplayDefault Input source setting Setting Projection mode StandardInput select Toggle Computer Video/S-Video Command Volume IncreaseEnlargement reset DecreaseReplacement lamp Specifications