Toshiba B-570 manual Print Tone Fine Adjustment, Thermal transfer printing fine adjustment

Page 55

6. DIAG. TEST OPERATION

EM18-33010A (Revision Date: Jan. 14 ‘99)

6.3 PARAMETER SETTING MODE

6.3.5Print Tone Fine Adjustment

Power off

Turn on the power while holding down the [FEED] key and [PAUSE] key.

< 1 > D I A G N O S T I C

V 1 . 0 A

Press the [FEED] key.

< 2 > P A R A M E T E R S E T

Press the [PAUSE] key five times.

T O N E A D J U S T < T >

+ 0

Press the [FEED] or [RESTART] key to adjust the feed length.

(See NOTE 1.)

Press the [PAUSE] key. (See NOTE 3.)

T O N E A D J U S T < D >

+ 0

Press the [FEED] or [RESTART] key to fine adjust the print tone. (See NOTE 1.)

(Thermal transfer printing fine adjustment)

■ [FEED] key:	Pressing the [FEED] key one
	time is a -1 step change, up to
	-10 steps. (See NOTE 2.)

■[RESTART] key: Pressing the [RESTART] key one time is a +1 step change, up to +10 steps. (See NOTE 2.)

(Thermal direct printing fine adjustment)

■ [FEED] key:	Pressing the [FEED] key one
	time is a -1 step change, up to
	-10 steps. (See NOTE 2.)

■[RESTART] key: Pressing the [RESTART] key one time is a +1 step change, up to +10 steps. (See NOTE 2.)

Press the [FEED] key and [RESTART] key at the same time.

Press the [PAUSE] key.

Continued on Section 6.3.6 Character code selection.

NOTES: 1 Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enables a fast forward.

2.A changed print tone value is stored in memory by pressing the [PAUSE] key.

3.Fine adjustment value equals to the sum of the values set by the PC command and system mode (key operation) and each max. value is ± 10 step. However, the upper limit of the adjustment value is decided according to the print speed to protect the print head. If the set value exceeds the following upper limit, it is automatically corrected to the proper value.

Upper Limit: 3”/sec.: +10 step, 5’’/sec.: +5 step, 8”/sec,: +2 step

6-24

Image 55

Contents Series Table of Contents Checks ProcedureDisconnect power cord before replacing important parts Major Unit ReplacementReplacing the PS UNIT, I/F PC Board and CPU PC Board Cover and top cover An oscilloscope Turn the power off and mount the left sideReplacing the Stepping Motor Replacing the TAKE-UP Motor Replacing the Ribbon MotorsReplacing the Solenoid Head Up Link Solenoid Spring Pin Old type print head Replacing the Print HeadAdjusting the print head position New type print head Replacing the Platen and Feed Roller Replacing the Platen and Feed Roller Replacing the Ribbon Back Tension Block Replacing the Paper SensorReplacing the Pinch Roller Shaft ASS’Y Adjustment Correcting Skew Printing High Speed PC Interface Board B-4800-PC-QM Installation Procedure for the Optional EquipmentInstallation Procedure for the Optional Equipment Cutter Module B-4205-QM EM18-33010A SVO7A1003 Nov ’97 Mount the cutter cover with the two screws Adjusting the Cutter Guide PlatesRemoved Parts ’ty/Unit Front plate Expansion memory and drawing size Memory ModuleFanfold Paper Guide Module B-4905-FF-QM Mechanism Description Cutter Drive Cutter ModeHarness Wiring Toshiba TEC Dirty print head Clean the print headFasten the head lever completely Refer to page 2-3 to adjust RAM Clear Mode Parameter Setting ModeTest Print Mode Sensor Setting ModeOutline of the DIAG. Test Operation DIAG. Test OperationPress the Pause key. See Note L I N EU S E I N T E N a N C E C O U N T E R Self Test ModeMaintenance Counter Printing B B O NSample Print Print Condition ∙ Preset count ∙ Print speed Trans ParametersB B O N T R a N S M I S S I V E Automatic Diagnostic PrintingPress the Pause key On .2.3 Head Broken Element Check Kanji ROM Check Print Condition ∙ Preset count ∙ Print speedSample Print PROGRAM/MASK ROM CheckDram Check Eeprom CheckFlash Memory Card Check Sensor 1 Check With ribbon Ribbon end Print status content description of each sensor/switchLabel is removed Ribbon end sensor Non-transmissiveDIP SW Check Connector FCN-781P024-G/PEXP. I/O Check E R M a L H E a D C H E C K R M a L E N D A D ErrorHead Broken Element Check Press the Pause key twice Press the Feed key twicePress the Pause key Parameter Setting ModeParameter Setting Mode Table Press the Feed key Feed Length Fine AdjustmentE D a D J U S T Press the Pause key twice 2 Cut/Strip Position Fine AdjustmentT a D J U S T Press the Feed key Press the Pause key Back Feed Length Fine AdjustmentAt the same time On Section Axis fine adjustment Press the Pause key three timesCut Position Fine Adjustment Example Feed Length Fine Adjustment ExampleLabel pitch When using a label with a length of less than 38 mmCase Condition Are receivedStrip Position Fine Adjustment Example Back Feed Length Fine Adjustment Example D J U S T Axis Fine AdjustmentPress the Pause key On Section Print tone fine adjustment Press the Pause key four timesAxis Fine Adjustment Example Thermal transfer printing fine adjustment Print Tone Fine AdjustmentThermal direct printing fine adjustment At the same time On Section Font zero selection Character Code SelectionPress the Pause key seven times N T codeR O F O N T Font Zero SelectionFeed key or Restart Code Control Code SelectionRestart CodeM a N U a LN T R O L Press the Pause keySelect either ribbon type with Ribbon Type SelectionPress the Pause key ten times ∙ Transmissive ribbonPress the Pause key eleven times Ribbon Motor Drive Voltage Fine AdjustmentA T U S P E Strip Wait Status SettingPress the Pause key fourteen times Stacker SelectionA C K E R S Y S T E M O F F R E S H O L D R Threshold Manual Fine Adjustment for the Black Mark SensorPress the Pause key sixteen times Threshold Manual Fine Adjustment for the Feed Gap SensorR E S H O L D T Case How To Calculate Theshold Fine Adjustment ValueWhen using perforated labels transmissive sensor When using labels transmissive sensorWhen using labels with black marks reflective sensor Select either code with Kanji Code SelectionPress the Pause key 17 times N J I codeSelect the Euro font code with the Feed key or Euro Font Code SelectionPress the Pause key 18 times R O codeB O HRestart key at Transmission Control Mode SelectionDTR/DSR RTS/CTSPress the Pause key 20 times Reset Selection when the Input Prime Signal is onP U T P R I M EO N Pause key Test Print ModeNormal Test Print I N T C O N D I T I O NN S O R T R a N S M I S S I V E I N T S P E E DP E R F E E D B E L L E N G T HFeed key or Restart key From B of the preceding Test Print Sample Process Test Print ∙ Print Tone Fine Adjustment Value +Press the Pause key Bar code are printed on 5 labels From B of the nextThermistor Check Sensor Setting ModePress the Feed key three times Press the Feed key Press the Pause key twice Black Mark Sensor AdjustmentFeed Gap Sensor Adjustment Feed key Former value is displayed Paper End Setting for Black Mark SensorIndicates setting complete. Press the Pause key. See Note Paper End Setting for Feed Gap SensorPress the Pause key five times RAM Clear Mode Table RAM Clear ModeType OFFB0H M P L E T E Maintenance Counter ClearR a M C L E a R I N T E C O U N T E R C L E a RR a M E T E R C L E a R Parameter ClearSW# SetupFloppy Disk IBM PC/ATDD-MM-YYYY Down Load ProcedureROM Error Code