Dell (PERC) S100, PERC S300 manual Lost

Page 66

Table 7-4. Warning Messages: Dell Inc. PERC S100 or S300 Adapter BIOS (continued)

Warning Message	Corrective Action

WARNING: Found	This warning message appears when at least one virtual disk is
virtual disks	in a Failed state and Pause if Failed is set to ON at the
that are	PERC Virtual Disk Management utility.
Failed	The following message appears after the warning is displayed:
	--- Press <Enter> to continue, or <Ctrl><R>
	to enter setup ---
	Press <Enter> to allow the operating system to continue its
	boot, or press <Ctrl><R> to enter into the PERC Virtual Disk
	Management utility to investigate the cause of the Failed virtual
	disk.
	NOTE: A boot virtual disk that is in a Failed state prevents the
	operating system from booting.
	To investigate the cause, check for the following:
	• Determine if a single or multiple physical disks in a non-
	redundant virtual disk have failed. If "yes," data is lost. Recover
	the lost data from a backup storage source.
	• Determine if two or more physical disks in a redundant virtual
	disk have failed. If "yes," data is lost. Recover the lost data
	from a backup storage source.
	NOTE: For a RAID 10, if a single physical disk fails in each
	mirrored set, the redundant virtual disk goes to a Degraded status
	but data is not lost. If two physical disks fail in one of the mirrored
	sets, the redundant virtual disk goes to a Failed status and data is
	lost.

66

Troubleshooting

Image 66

Contents User’s Guide February Contents Installing the Microsoft Windows Drivers Installing the Perc S300 AdapterComplete the Hardware Installation Physical Disk-Related ErrorsRAID Technology Understanding Disk Arrays Industry Canada Notice Canada OnlyContents Page Safety General Safety When Working Inside Your SystemProtecting Against Electrostatic Discharge Page Overview IntroductionOverview Supported Platforms Requirements Physical disksOverview Boot to it About RAID Summary of RAID LevelsRAID Terminology Disk StripingDisk Mirroring Spanned RAID Levels Parity DataExample of Distributed Parity RAID Features General FeaturesDescription Description Allows hot-swapping Physical disks, in the same virtual disk Disks That supports hot-swappingBackplane with hot-swap capability Features Virtual disk Migration during an OCESpecifications RAID Hardware Installation Before You BeginGeneral Considerations Installing the Perc S300 Adapter Installing a Perc S300 Adapter Connecting the Cables Complete the Hardware Installation Connect Physical Disks to the Perc S300 AdapterHardware Installation Installing the Drivers Installing the Microsoft Windows DriversDownloading the Controller Driver Media Pre-Installation Requirements for the Controller Drivers Operating System And Device Driver MediaTo Use Sata Controller to either ATA Mode or Ahci Pre-Installation Procedures For The Controller Drivers Steps DVD, and so on, perform the following For Microsoft Windows Server 2008 and Windows Server 2008 R2 For Microsoft Windows Server For Microsoft Windows Server 2008 and Windows Server 2008 R2 Installing the Drivers Installing the Drivers RAID Configuration Management Perc Virtual Disk Management Utility Operations DescriptionAccessing the Perc Virtual Disk Management Utility Perc Virtual Disk Management Text Colors Description Initializing Physical Disks Creating Virtual Disks Before You BeginRAID Configuration and Management Deleting Virtual Disks RAID Configuration and Management Swapping Two Virtual Disks Managing Global Hot Spares Create a Global Hot SpareDelete a Global Hot Spare Viewing Physical Disk Details Viewing Virtual Disk DetailsController Options Description How to Operate Rescanning DisksController Options Continuing to Boot Pause if DegradedRAID Configuration and Management Troubleshooting System Startup ProblemsRAID Mode to ATA Mode Boot Mode, Boot Sequence Bios Bios Screen Corrective Action Lost This warning message appears when multiple virtual disks are Bios not Installed User Disabled INT13 Bios Load From virtual disk creation Virtual Disk-Related Errors On the virtual disk A Virtual Disk is in a Failed StateRedundant virtual disk 12. Cannot Create a Global Hot Spare Select View Virtual Disk Details Physical Disk-Related Errors 14. a Dedicated Hot Spare FailsTroubleshooting Read, Write, and Cache Policy Controller SpecificationsAppendix a S300 adapterTable A-3. Physical Disk Tasks Physical Disk Task Name Controller TasksPhysical Disk Tasks Perc S300 adapterTable A-4. Virtual Disk Tasks Virtual Disk Task Name Virtual Disk TasksSupported RAID Levels AdapterVirtual Disk Specifications Appendix B RAID Technology Understanding Disk Arrays and Virtual DisksUnderstanding RAID Levels Appendix B Disk States Virtual and Physical Disks Table B-2. Physical Disk States DefinitionFailure States Table B-3. Virtual Disk States State DefinitionUnderstanding Physical Disks Table B-5. Minimum and Maximum Physical Disk ConfigurationsCreating Virtual Disks Future Expansion Physical Disk StatesDedicated Hot Spares Rescanning Physical Disks for Changes in StateGlobal Hot Spares Appendix C Regulatory NoticesFCC Notice U.S. Only FCC, Class aFCC, Class B Industry Canada, Class a Industry Canada Notice Canada OnlyCE Notice European Union Industry Canada, Class BAppendix C CE Mark Notice Appendix D Contacting DellAppendix D Index Index Index 100 101 102 Glossary 103104 105 106 107 Acronym for nanoseconds, one billionth of a second108 109 110