Dell XPS410 manual Installing Memory, Addressing Memory With 4-GB Configurations

Page 16

¡A pair of matched memory modules installed in connectors DIMM_1 and DIMM_2

or

¡A pair of matched memory modules installed in connectors DIMM_1 and DIMM_2 and another matched pair installed in connectors DIMM_3 and DIMM_4

If you install mixed pairs of DDR2 533-MHz (PC2-4300), DDR2 667-MHz (PC2-5300), and DDR2 800-MHz (PC2-6400) memory, the modules function at the slowest speed installed.

Be sure to install a single memory module in the DIMM_1 connector, the connector closest to the processor, before you install modules in the other connectors.

While installing memory modules, ensure that you do not mix ECC and non-ECC memory.

1

Channel A: matched pair of memory modules in connectors DIMM_1 and DIMM_2 (white securing clips)

2

Channel B: matched pair of memory modules in connectors DIMM_3 and DIMM_4 (black securing clips)

NOTE: Memory purchased from Dell is covered under your computer warranty.

NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that you may have, even if you purchased the new modules from Dell. If possible, do not pair an original memory module with a new memory module. Otherwise, your computer may not start properly. You should install your original memory modules in pairs either in connectors DIMM_1 and DIMM_2 or connectors DIMM_3 and DIMM_4.

Addressing Memory With 4-GB Configurations

Your computer supports a maximum of 4 GB of memory when you use four 1-GB DIMMs. Current operating systems, such as Microsoft® Windows® XP, can only use a maximum of 4 GB of address space; however, the amount of memory available to the operating system is less than 4 GB. Certain components within the computer require address space in the 4-GB range. Any address space reserved for these components cannot be used by computer memory.

Installing Memory

CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide.

NOTICE: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer.

1.Follow the procedures in Before You Begin.

2.Remove the computer cover (see Removing the Computer Cover).

3.Lay the computer on its side so that the system board is on the bottom of the inside of the computer.

4.Press out the securing clip at each end of the memory module connector.

Image 16
Contents Model Dcta August 2006 Rev. A00 About Your Computer Front View of the ComputerBack Panel Connectors Back View of the ComputerBack to Contents Advanced Troubleshooting Power LightsDiagnostic Lights Problem Description Suggested ResolutionBeep Codes Code CauseSystem setup see Entering System Setup Message Possible Cause Corrective ActionDell Diagnostics Dell Diagnostics Main MenuOption Function Tab FunctionDrivers Reinstalling DriversIdentifying Drivers Resolving Software and Hardware Incompatibilities Click Start, then click Help and SupportBefore You Begin Getting StartedRecommended Tools Turning Off Your ComputerBack to Contents Removing and Installing Parts Removing the Computer CoverInside View of Your Computer System Board ComponentsMemory Memory OverviewInstalling Memory Addressing Memory With 4-GB ConfigurationsPage Removing Memory CardsPCI Cards Page Page PCI Express Cards Removing a PCI CardPage Page Removing a PCI Express Card Drive Panels Removing the Drive PanelInstalling the Drive-Panel Insert Removing the Drive-Panel InsertInstalling the Drive Panel DrivesHard Drive General Installation GuidelinesRemoving a Hard Drive Installing a Hard Drive Adding a Second Hard Drive Floppy Drive Removing a Floppy DriveInstalling a Floppy Drive Media Card ReaderRemoving a Media Card Reader Installing a Media Card Reader CD/DVD Drive Installing a CD/DVD DriveRemoving a CD/DVD Drive Battery Power Supply Replacing the BatteryRemoving the Power Supply Installing the Power SupplyProcessor Removing the ProcessorInstalling the Processor Page Panel Components PanelRemoving the I/O Panel Page Installing the I/O Panel Processor Fan Removing the Processor FanInstalling the Processor Fan Card FanInstalling the Card Fan System BoardRemoving the Card Fan Removing the System BoardInstalling the System Board Replacing the Computer CoverBack to Contents Specifications Drives ConnectorsControls and Lights Physical PowerEnvironmental System Setup Program Entering System SetupSystem Setup Screens System Setup OptionsDrives Boot Sequence Option SettingsChanging Boot Sequence for the Current Boot Clearing Forgotten PasswordsChanging Boot Sequence for Future Boots Clearing Cmos Settings Flashing the Bios Technical Overview Power Supply DC Connector Pin Assignments DC Power Connector P1 Signal Name Color Wire GaugeDC Power Connector P2 DC Power Connect P4DC Power Connect P3, P5, P8, P9, P13, and P14 DC Power Connector P7DC Power Connectors P10 DC Power Connector P12
Related manuals
Manual 63 pages 47.98 Kb Manual 63 pages 48.17 Kb

XPS410, 410 specifications

The Dell XPS 410, launched in the mid-2000s, was a prominent desktop computer known for its robust performance and modern design. Targeting both enthusiasts and everyday users, the XPS 410 emerged as a reliable option for gaming, media, and general computing tasks.

One of the standout features of the XPS 410 was its sleek and stylish appearance, designed to complement contemporary home and office environments. It boasted a stylish chassis with an integrated lighting system, showcasing Dell's commitment to aesthetics alongside functionality.

The XPS 410 was powered by Intel's Core 2 Duo processor, which offered significant improvements in performance and energy efficiency over its predecessors. Depending on the configuration, users could choose from various processors, allowing for customization based on personal needs. This flexibility made the XPS 410 suitable for resource-intensive applications, such as photo editing, video rendering, and gaming.

Accompanying the powerful processor was a choice of memory options, with support for up to 4GB of DDR2 RAM. This ample memory capacity ensured smooth multitasking and efficient handling of demanding software. Users could also enhance performance through options for high-speed graphics cards, with dedicated GPUs from NVIDIA and ATI, catering to the needs of gamers and graphic designers alike.

In terms of storage, the XPS 410 offered various hard drive configurations, with SATA drives ranging from 250GB to 750GB, ensuring ample space for files, applications, and multimedia. Additionally, with options for RAID configurations, users could benefit from increased data redundancy and improved performance.

The XPS 410 also incorporated advanced technologies such as Dell's Media Center remote control compatibility, allowing for convenient navigation and control of media applications. The inclusion of multiple USB ports and card reader slots made it easy for users to connect a variety of peripherals, enhancing the overall functionality of the system.

Another noteworthy aspect of the XPS 410 was its ability to run Windows Vista, further emphasizing its appeal during a time of transition in consumer operating systems. The combination of powerful hardware and versatile software offerings made the XPS 410 a favored choice among professionals and gamers alike.

In summary, the Dell XPS 410 was a well-rounded desktop computer, featuring powerful processors, ample memory and storage options, and an appealing design. It catered to a wide variety of users, providing performance and versatility that stood out in its era.