Dell 8200 technical specifications Replacing the Microprocessor

Page 20

8.Remove the two shorter, green plastic rails from the inside of the computer cover.

These rails are not attached to the computer cover with screws. To remove the rails, firmly pull the rails from the drive cage.

9.Attach the rails to the drive using the screws supplied with the drive.

Ensure that the rail tabs are positioned at the back of the drive.

10.Gently slide the drive into the bay until you hear a click.

11.Carefully replace the drive bay cover.

You do not need to replace the cover insert.

12.Connect a power cable to the drive.

See the documentation that came with the drive for instructions on connecting a drive cable to the drive.

HINT: Your computer uses cable-select drive cables. This means that the device connected to the end connector of the drive cable is the master device and the device connected to the middle connector is the slave device. Be sure the jumper setting on the new device is set for "cable select" (see the documentation that came with the drive for information).

13.Close the computer cover.

14.Connect your computer and devices to their electrical outlets, and turn them on.

NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.

15.Install any drivers required for the drive as described in the documentation that came with the drive.

Replacing the Microprocessor

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in "Safety Instructions."

1.Shut down the computer.

2.Turn off any attached devices and disconnect them from their electrical outlets.

Image 20
Contents Abbreviations and Acronyms Dell DimensionHints, Notices, and Cautions System Codes and Messages Diagnostic CodesDiagnostic Code Definition Corrective Action Post Beep Codes System MessagesBeep Codes Possible Cause Corrective Action Message Possible Cause Corrective ActionPost Documentation Printed DocumentationOnline Documentation Downloading the Tell Me How Help File and Associated FilesAdding Parts Safety InstructionsWhen Using Your Computer When Working Inside Your Computer Protecting Against Electrostatic DischargeShutting Down the Computer Reattaching the Front Door and Hinge ArmsReattaching the Hinge Arms Opening the Computer Cover Adding CardsOpen the computer cover Removing Cards Close the computer coverAdding Memory Rdram OverviewShut down the computer Replacing an AGP Card Adding a Second Hard Drive Adding Other Drives Inch Devices Inch Devices Replacing the Microprocessor Open the computer cover Installing the Microprocessor Removing the Front I/O Panel Replacing the Power SupplyRemoving the Power Supply Replacing the System Board Replacing the Power SupplyDimension 8200 System Board Types Removing the System Board Closing the Computer Cover Replacing the System BoardALERT! Cover was previously removed Power Problems Solving ProblemsAccessing Help Files Start-Up Error Messages Video and Monitor ProblemsAdjust the Windows display settings If the screen is blankSound and Speaker Problems Printer ProblemsIf you cannot print to a parallel port printer If you cannot print to a USB printerScanner Problems Modem ProblemsVerify that the modem is communicating with Windows Control Panel, double-clickPhone and Modem OptionsMouse Problems Keyboard ProblemsDrive Problems Check the mouse settingsIf you have a hard drive problem Under Error-checking, click Check NowIf you cannot play a DVD movie If the CD-RW drive stops writingGeneral Program Problems Network ProblemsMicrosoft Windows Error Messages Resolving Other Technical Problems Internet Connection ProblemsMail Problems Reinstalling Drivers Using the Windows XP Device Driver RollbackAt the Welcome Dell System Owner screen, click Next Click PropertiesWindows Resolving Software and Hardware IncompatibilitiesWindows Me Using System Restore Creating a Restore PointReinstalling Windows XP Undoing the Last System RestoreClick Create a restore point Restoring the Computer to an Earlier Operating StateReinstalling Windows Me Click I accept the Agreement, and then click Next Reinstalling WindowsClick Next in the Welcome to Windows Me window Press Enter again to restart your computer Technical Specifications Power Audio2Video Controls and LightsBack to Contents System Setup Program Viewing SettingsSystem Setup Program Screens OverviewOption Function Clearing Forgotten Passwords PXE BISInternal View System Board Connectors and Sockets Technical OverviewPower Supply Socketed MicroprocessorDC Power Connectors Pin Number Signal name 18-AWG WireDC Power Connector P2 DC Power Connectors P3, P5, P6, P8, and P9DC Power Connector P7 Pin Number Signal Name 22-AWG WireIDE Interface Cable Connections for Dell-Installed Drives Placement of Dell-Installed CardsIDE Channel Connector Location Dell Installed Drive Card Connector Card DescriptionControls and Lights Front ViewBack View Windows LabelSerial Connector Hints, Notices, and Cautions Abbreviations and Acronyms
Related manuals
Manual 150 pages 39.74 Kb Manual 162 pages 52.76 Kb