D-Link DSL-522T manual Wizard

Page 20

DSL-522T ADSL Router User Guide

Wizard

To use the Setup Wizard, click the Run Wizard button in the first browser window and follow the instructions in the pop-up window that appears.

The initial window summarizes the setup process. Click the Next button to proceed. You may stop using the Setup Wizard at any time by clicking the Exit button. If you exit the wizard you will return to the Setup Wizard window without saving any of the settings changed during the process.

The first pop-up window of the Setup Wizard lists the basic steps in the process. These steps are as follows:

1.Set the system time.

2.Configure the connection to the Internet.

3.Save the new configuration settings and reboot the system.

10

Image 20

Contents DSL-522T Adsl Router User Guide Table Of Contents Status Installation Overview Setup WizardBefore You Start Packing ListInstallation Notes Password WAN SettingUsername Connection TypeInstalling the USB Driver Viii DSL-522T Adsl Router User Guide Page Introduction Router Description and OperationRouter Features Front Panel Display Rear Panel Connections Connect network cablesFactory Reset Button Hardware InstallationPower on Router Connect Router to Ethernet Network ConnectionsConnect Adsl Line Configuration Summary Basic Router ConfigurationComputer IP Settings Enter Password Access the Configuration ManagerLogin to Home Configure the Router Web Manager First Time Log OnWizard Using the Setup Wizard Choose Time Zone Using the Setup Wizard Choose Connection Type Using the Setup Wizard For PPPoE/PPPoA connections Using the Setup Wizard For Dynamic IP Address connections Using the Setup Wizard For Static IP Address connections Using the Setup Wizard For Bridge Mode connections Using the Setup Wizard Finish and Restart Bridge Mode WAN Settings window Bridge ModeDSL-522T Adsl Router User Guide WAN Settings window Dynamic IP Address Dynamic IP AddressDSL-522T Adsl Router User Guide Dynamic IP Parameters Description Cloned MAC AddressMAC Address button FirewallWAN Settings window Static IP Static IP AddressDSL-522T Adsl Router User Guide Static IP Parameters Description WAN Settings window PPPoE/PPPoA PPPoE/PPPoADSL-522T Adsl Router User Guide Default Route PPPoE/PPPoA Description ParametersUser Name IP ControlATM Settings for WAN connection Service CategoryATM Traffic Shaping ATM Parameters DescriptionATM VC Settings ATM VC Settings in WAN Settings windowATM VC Parameters Description Virtual CircuitLAN Management IP windowDhcp Settings window DhcpDisable the Dhcp Server Use the Router for DhcpDhcp Settings window with Dhcp disabled Static IP on LAN DNS Configuration window DNSDynamic DNS Ddns Parameters DescriptionSave Settings and Reboot System Settings windowMultiple Virtual Connections Configure Multiple PVCsSelect new PVC to configure in the WAN Settings window Configure new PVC Configuration and Read-only Windows Advanced Router ManagementDirectory Home Advanced Tools Status HelpUPnP UPnP windowVirtual Server Virtual Server windowCategory Available Rules Custom Forwarding Rules LAN Clients LAN Clients windowSnmp Category Parameters Snmp Management windowSnmp Management CommunityFilters Filters windowFilters Parameter Description Bridge Filters Bridge Filters windowStatic Routing Routing Table windowDMZ DMZ windowFirewall Dos Protection Port Scan Protection Service FilteringFirewall Configura Tion window RIP System Wide Configuration window RIPPPP PPP Connection windowAdsl Configuration window AdslATM VC Setting window ATM VCCAdministrator Settings window ToolsTop section of the Administrator Settings menu Change System PasswordRemote Web Management and Remote Telnet Access Time Time menuRemote Log Settings window Remote LogSave or Load Configuration File Restore Factory Default SettingsFirmware Upgrade Firmware Upgrade windowMiscellaneous Configuration Miscellaneous Configuration windowPing Test Igmp ProxyDiagnostic Test Diagnostic Test windowDevice Information window StatusDevice Info Dhcp Clients Log View Log windowStatistics Traffic Statistics windowAdsl Status Adsl Status informationHelp Help windowTechnical Specifications Adsl Standards ADSL2 StandardsInput 120V AC 60Hz Output 9V DC, 1AWatts max To 40CControl Panel Configuring IP Settings on Your ComputerConfigure Windows XP for Dhcp Click Network and Internet Connections Click Network ConnectionsSelect Obtain an IP address Configure Windows 2000 for Dhcp WindowsConfigure Windows 95 and Windows 98 for Dhcp Windows 95 and WindowsWindows ME Click the Obtain an IP address automatically optionWindows NT 4.0 Workstations Configure Windows ME for DhcpConfigure Windows NT 4.0 for Dhcp In-line low pass filter Low Pass Filters for DSLIn-Line Filter Three Port Filter Port FilterInternational Offices Switzerland