D-Link manual DSL-522T Adsl Router User Guide

Page 29

DSL-522T ADSL Router User Guide

connection software requires the user to enter the User Name and Password for the ISP account. This information is stored on the computer, not in the Router.

Follow the instructions below to configure a Bridged connection for the WAN interface.

To configure a Dynamic IP Address connection, perform the steps listed below. Some of the settings do not need to be changed the first time the device is set up, but can be changed later if you choose. See the table below for a description of all the settings available in this window.

1.Choose the Bridge Mode option from the WAN Settings pull-down menu.

2.Under the ATM VC Settings at the top of the window should not be changed unless you have been instructed to change them. However, if you are instructed to change the VPI or VCI values, type in the values assigned for your account. Leave the PVC and Virtual Circuit setting at the default (Pcv0 and Enabled) values for now. This can be used later if you are configuring multiple virtual circuits for your ADSL service. For more information, see the section on ATM VC Settings later in this manual.

3.Under the Bridge Mode heading, choose the Connection Type from the pull-down menu. This defines both the connection type and encapsulation method used for your ADSL service. The available options are 1483 Bridged IP LLC and 1483 Bridged IP VC-Mux.If have not been provided specific information for the Connection Type setting, leave the default setting.

4.Most users will not need to change ATM settings. If this is the first time you are setting up the ADSL connection it is recommended that you leave the Service Category settings at the default values until you have established the connection. See the section on ATM Traffic Shaping later in this manual for a further description of the parameters available for ATM traffic shaping.

5.When you are satisfied that all the WAN settings are configured correctly, click on the Apply button.

6.The new settings must be saved and the Router must be restarted for the settings to go into effect. To save and reboot the Router, click on the Tools directory tab and then click the System button. In the System Settings window, click the Save and Reboot button under Save Settings and Reboot the System.

7.Click OK when the following “Save and restart?” dialog box opens.

8.The Router will save the new settings and restart. Upon restarting the Router will automatically establish the WAN connection.

19

Image 29
Contents DSL-522T Adsl Router User Guide Table Of Contents Status Setup Wizard Installation OverviewBefore You Start Packing ListInstallation Notes WAN Setting PasswordUsername Connection TypeInstalling the USB Driver Viii DSL-522T Adsl Router User Guide Page Router Description and Operation IntroductionRouter Features Front Panel Display Connect network cables Rear Panel ConnectionsFactory Reset Button Hardware InstallationPower on Router Connect Router to Ethernet Network ConnectionsConnect Adsl Line Configuration Summary Basic Router ConfigurationComputer IP Settings Enter Password Access the Configuration ManagerLogin to Home Web Manager First Time Log On Configure the RouterWizard Using the Setup Wizard Choose Time Zone Using the Setup Wizard Choose Connection Type Using the Setup Wizard For PPPoE/PPPoA connections Using the Setup Wizard For Dynamic IP Address connections Using the Setup Wizard For Static IP Address connections Using the Setup Wizard For Bridge Mode connections Using the Setup Wizard Finish and Restart WAN Settings window Bridge Mode Bridge ModeDSL-522T Adsl Router User Guide Dynamic IP Address WAN Settings window Dynamic IP AddressDSL-522T Adsl Router User Guide Cloned MAC Address Dynamic IP Parameters DescriptionMAC Address button FirewallStatic IP Address WAN Settings window Static IPDSL-522T Adsl Router User Guide Static IP Parameters Description PPPoE/PPPoA WAN Settings window PPPoE/PPPoADSL-522T Adsl Router User Guide PPPoE/PPPoA Description Parameters Default RouteUser Name IP ControlService Category ATM Settings for WAN connectionATM Traffic Shaping ATM Parameters DescriptionATM VC Settings in WAN Settings window ATM VC SettingsATM VC Parameters Description Virtual CircuitManagement IP window LANDhcp Dhcp Settings windowUse the Router for Dhcp Disable the Dhcp ServerDhcp Settings window with Dhcp disabled Static IP on LAN DNS DNS Configuration windowDdns Parameters Description Dynamic DNSSystem Settings window Save Settings and RebootMultiple Virtual Connections Configure Multiple PVCsSelect new PVC to configure in the WAN Settings window Configure new PVC Advanced Router Management Configuration and Read-only WindowsDirectory Home Advanced Tools Status HelpUPnP window UPnPVirtual Server window Virtual ServerCategory Available Rules Custom Forwarding Rules LAN Clients window LAN ClientsSnmp Management window Snmp Category ParametersSnmp Management CommunityFilters window FiltersFilters Parameter Description Bridge Filters window Bridge FiltersRouting Table window Static RoutingDMZ window DMZFirewall Dos Protection Port Scan Protection Service FilteringFirewall Configura Tion window RIP RIP System Wide Configuration windowPPP Connection window PPPAdsl Adsl Configuration windowATM VCC ATM VC Setting windowTools Administrator Settings windowTop section of the Administrator Settings menu Change System PasswordRemote Web Management and Remote Telnet Access Time menu TimeRemote Log Remote Log Settings windowRestore Factory Default Settings Save or Load Configuration FileFirmware Upgrade window Firmware UpgradeMiscellaneous Configuration window Miscellaneous ConfigurationPing Test Igmp ProxyDiagnostic Test window Diagnostic TestDevice Information window StatusDevice Info Dhcp Clients View Log window LogTraffic Statistics window StatisticsAdsl Status information Adsl StatusHelp window HelpAdsl Standards ADSL2 Standards Technical SpecificationsOutput 9V DC, 1A Input 120V AC 60HzWatts max To 40CControl Panel Configuring IP Settings on Your ComputerConfigure Windows XP for Dhcp Click Network Connections Click Network and Internet ConnectionsSelect Obtain an IP address Windows Configure Windows 2000 for DhcpWindows 95 and Windows Configure Windows 95 and Windows 98 for DhcpWindows ME Click the Obtain an IP address automatically optionWindows NT 4.0 Workstations Configure Windows ME for DhcpConfigure Windows NT 4.0 for Dhcp In-line low pass filter Low Pass Filters for DSLIn-Line Filter Port Filter Three Port FilterSwitzerland International Offices