D-Link DSL-522T manual WAN Settings window PPPoE/PPPoA

Page 36

DSL-522T ADSL Router User Guide

PPPoE/PPPoA

Follow the instructions below to configure the Router to use a PPPoE or PPPoA for the Internet connection. Make sure you have all the necessary information before you configure the WAN connection.

WAN Settings window – PPPoE/PPPoA

To set up a PPPoE or PPPoA connection:

1.If not already selected, choose the PPPoE/PPPoA option from the WAN Settings pull-down menu. PPPoE/PPPoA is selected by default if you are configuring the Router for the first time.

2.Under the ATM VC Settings at the top of the window should not be changed unless you have been instructed to change them. However, if you are instructed to change the VPI or VCI values, type in the values assigned for your account. Leave the PVC and Virtual Circuit setting at the default (Pcv0 and Enabled) values for now. This can be used later if you are configuring multiple virtual circuits for your ADSL service. For more information, see the section on ATM VC Settings later in this manual.

26

Image 36
Contents DSL-522T Adsl Router User Guide Table Of Contents Status Installation Overview Setup WizardBefore You Start Packing ListInstallation Notes Password WAN SettingUsername Connection TypeInstalling the USB Driver Viii DSL-522T Adsl Router User Guide Page Introduction Router Description and OperationRouter Features Front Panel Display Rear Panel Connections Connect network cablesHardware Installation Power on RouterFactory Reset Button Network Connections Connect Adsl LineConnect Router to Ethernet Basic Router Configuration Computer IP SettingsConfiguration Summary Access the Configuration Manager Login to HomeEnter Password Configure the Router Web Manager First Time Log OnWizard Using the Setup Wizard Choose Time Zone Using the Setup Wizard Choose Connection Type Using the Setup Wizard For PPPoE/PPPoA connections Using the Setup Wizard For Dynamic IP Address connections Using the Setup Wizard For Static IP Address connections Using the Setup Wizard For Bridge Mode connections Using the Setup Wizard Finish and Restart Bridge Mode WAN Settings window Bridge ModeDSL-522T Adsl Router User Guide WAN Settings window Dynamic IP Address Dynamic IP AddressDSL-522T Adsl Router User Guide Dynamic IP Parameters Description Cloned MAC AddressMAC Address button FirewallWAN Settings window Static IP Static IP AddressDSL-522T Adsl Router User Guide Static IP Parameters Description WAN Settings window PPPoE/PPPoA PPPoE/PPPoADSL-522T Adsl Router User Guide Default Route PPPoE/PPPoA Description ParametersUser Name IP ControlATM Settings for WAN connection Service CategoryATM Traffic Shaping ATM Parameters DescriptionATM VC Settings ATM VC Settings in WAN Settings windowATM VC Parameters Description Virtual CircuitLAN Management IP windowDhcp Settings window DhcpDisable the Dhcp Server Use the Router for DhcpDhcp Settings window with Dhcp disabled Static IP on LAN DNS Configuration window DNSDynamic DNS Ddns Parameters DescriptionSave Settings and Reboot System Settings windowConfigure Multiple PVCs Select new PVC to configure in the WAN Settings windowMultiple Virtual Connections Configure new PVC Configuration and Read-only Windows Advanced Router ManagementDirectory Home Advanced Tools Status HelpUPnP UPnP windowVirtual Server Virtual Server windowCategory Available Rules Custom Forwarding Rules LAN Clients LAN Clients windowSnmp Category Parameters Snmp Management windowSnmp Management CommunityFilters Filters windowFilters Parameter Description Bridge Filters Bridge Filters windowStatic Routing Routing Table windowDMZ DMZ windowDos Protection Port Scan Protection Service Filtering Firewall Configura Tion windowFirewall RIP System Wide Configuration window RIPPPP PPP Connection windowAdsl Configuration window AdslATM VC Setting window ATM VCCAdministrator Settings window ToolsChange System Password Remote Web Management and Remote Telnet AccessTop section of the Administrator Settings menu Time Time menuRemote Log Settings window Remote LogSave or Load Configuration File Restore Factory Default SettingsFirmware Upgrade Firmware Upgrade windowMiscellaneous Configuration Miscellaneous Configuration windowPing Test Igmp ProxyDiagnostic Test Diagnostic Test windowStatus Device InfoDevice Information window Dhcp Clients Log View Log windowStatistics Traffic Statistics windowAdsl Status Adsl Status informationHelp Help windowTechnical Specifications Adsl Standards ADSL2 StandardsInput 120V AC 60Hz Output 9V DC, 1AWatts max To 40CConfiguring IP Settings on Your Computer Configure Windows XP for DhcpControl Panel Click Network and Internet Connections Click Network ConnectionsSelect Obtain an IP address Configure Windows 2000 for Dhcp WindowsConfigure Windows 95 and Windows 98 for Dhcp Windows 95 and WindowsWindows ME Click the Obtain an IP address automatically optionConfigure Windows ME for Dhcp Configure Windows NT 4.0 for DhcpWindows NT 4.0 Workstations Low Pass Filters for DSL In-Line FilterIn-line low pass filter Three Port Filter Port FilterInternational Offices Switzerland