D-Link DSL-2740B manual Configure Windows 2000 for Dhcp

Page 111

Windows 2000

First, check for the IP protocol and, if necessary, install it:

1.In the Windows task bar, click the Start button, point to Settings, and then click Control Panel.

2.Double-click the Network and Dial-up Connections icon.

3.In the Network and Dial-up Connections window, right-click the Local Area Connection icon, and then select Properties.

4.The Local Area Connection Properties dialog box displays with a list of currently installed network components. If the list includes Internet Protocol (TCP/IP), then the protocol has already been enabled, skip ahead to Configure Windows 2000 for DHCP.

5.If Internet Protocol (TCP/IP) does not display as an installed component, click Install.

6.In the Select Network Component Type dialog box, select Protocol, and then click Add.

7.Select Internet Protocol (TCP/IP) in the Network Protocols list, and then click OK.

8.You may be prompted to install files from your Windows 2000 installation CD or other media. Follow the instructions to install the files.

9.If prompted, click OK to restart your computer with the new settings.

Configure Windows 2000 for DHCP

1.In the Control Panel, double-click the Network and Dial-up Connections icon.

2.In Network and Dial-up Connections window, right-click the Local Area Connection icon, and then select Properties.

3.In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP), and then click Properties.

4.In the Internet Protocol (TCP/IP) Properties dialog box, click the button labeled Obtain an IP address automatically.

5.Double-click OK to confirm and save your changes, and then close the Control Panel.

Your computer is now ready to use the Router’s DHCP server.

101

Image 111
Contents DSL-2740B WirelessADSL2+ Router User Guide FCC Warning CE Mark WarningTable Of Contents Save / REBOOTt 104 Installation Overview Setup WizardAbout This User Guide Packing List Installation NotesAdditional Software Key Security ProtocolIP Address Radius server PortEthernet NIC LAN IP addresses forDSL-2740B LAN Subnet Mask forRouter Description and Operation 802.11n-draft WirelessRouter Features Standards Compatibility and Compliance Power Front Panel DisplayInternet Connect network cables Rear Panel ConnectionsRange Setting Up a Wireless NetworkWireless Security RadioLocation and Wireless Operation Factory Reset Button Power on RouterHub or Switch to Router Connection Connect Adsl LineConnect Router to Ethernet Computer to Router Connection DSL-2740B Wireless Adsl Router User Guide Configuration Summary Configuring IP Settings on Your ComputerAccess the Configuration Manager Login to HomeEnter Password Web Manager First Time Log On Configure the RouterWizard Using the Setup Wizard WAN Settings PVC SettingsUsing the Setup Wizard WAN Settings Choose Connection Type DSL-2740B Wireless Adsl Router User Guide Using the Setup Wizard For PPPoE/PPPoA connection Use Static IP Address Enable PPP Debug ModeDial on demand PPP IP extensionUsing the Setup Wizard For Dynamic IP 1483 Bridge connection Select the specific Connection Type and Encapsulation Mode Using the Setup Wizard For Static IP Address IPoA connection Using the Setup Wizard For Bridge Mode connections Using the Setup Wizard For LAN Settings Using the Setup Wizard For Wireless LAN Settings Using the Setup Wizard Finish and Restart Adsl ATM Settings Adsl Settings WindowVirtual Circuit Service Category Primary DNS Address Router SettingsDefault Route FirewallWlan Wlan Settings WindowLAN LAN Settings Window Igmp Snooping UPnPDNS DNS Configuration windowPage Setup AdvancedTools Status Advanced Adsl Window Advanced AdslAdvanced Wlan Window Advanced WlanWEP Wlan SecurityWlan Security Window WEP 802.1xWlan Security Window WPA-PSKWlan Security Window WPA-PSK WPA Wi-Fi Protected AccessWlan Security Window WPA Wlan FilterWlan Filter Window Wlan BridgeWlan Bridge Window Wlan QOS Wlan QoS Window Firewall Firewall Window Virtual Server Protocol Port TriggeringServer IP Address External Port Start/EndPort Triggering Window DMZ Open Protocol Opened protocol for remote usersDMZ Window Outgoing IP Filter Outgoing IP Filter Window Incoming IP Filter Incoming IP Filter Window Bridge FilterBridge Filter Window Parent Control Parent Control Window URL FilterURL Filter Window Quality of ServiceQuality of Service Window Routing Routing Window RIPRIP Window RIP Parameters DescriptionOperation Port MappingInterface VersionPort Mapping Window Port Mapping Window Tools Diagnostics WindowBackup Settings window Backup SettingsUpdate Settings Restore DefaultUpdate Settings Window TR069 Client Restore Default WindowTR-069 Client Window Snmp ConfigurationDdns Snmp Configuration WindowDdns Window Time Time Window Access ServiceAccess Service Window Access IP Password Access IP WindowPassword Window Save / REBOOTt Update FirmwareSave / Reboot Window Device Info window Device InfoAdsl Window LAN Window WANWAN Window ATMATM Window RouteRoute Window ARPARP Window Dhcp ClientsDhcp Clients window Wlan StationWlan Station Window System LOGSystem LOG window System Log Category ParametersPage System LOG window Adsl Standards ADSL2 Standards Technical SpecificationsTo 40C Input 120V AC 60HzOutput 12V AC, 1200mA Watts maxWireless Control Panel Configure Windows XP for DhcpClick Network Connections Click Network and Internet ConnectionsSelect Obtain an IP address Click PropertiesWindows Configure Windows 2000 for DhcpWindows ME Configure Windows 95 and Windows 98 for DhcpConfigure Windows ME for Dhcp Windows 95 and WindowsWindows NT 4.0 Workstations Configure Windows NT 4.0 for DhcpIn-line low pass filter In-Line FilterPort Filter Three Port Filter