Linksys WET200 manual Appendix E, Regulatory Information

Page 33

Appendix E

Appendix E: Regulatory Information

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•• Reorient or relocate the receiving antenna

•• Increase the separation between the equipment or devices

•• Connect the equipment to an outlet other than the receiver’s

•• Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the USA is firmware-limited to channels 1 through 11.

Regulatory Information

Safety Notices

•• Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.

•• Do not use this product near water, for example, in a wet basement or near a swimming pool.

•• Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

WARNING: This product contains lead, known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003 and RSS210.

Operation is subject to the following two conditions:

1.This device may not cause interference and

2.This device must accept any interference, including interference that may cause undesired operation of the device. This device has been designed to operate with an antenna having a maximum gain of 2dBi. Antenna havingahighergainisstrictlyprohibitedperregulations of Industry Canada. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication.

Industry Canada Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Wireless-G Business Ethernet Bridge

29

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Wireless-G Business Ethernet Bridge About This Guide About This GuideIcon Descriptions Online ResourcesTable of Contents Appendix a Wireless Security Checklist Appendix B GlossaryAppendix E Regulatory Information Chapter Introduction ChapterChapter Planning Your Wireless Network Network TopologyNetwork Layout Example of WET200 in Ad-Hoc Mode Product Overview Chapter Product OverviewFront Panel Back PanelInstallation Chapter InstallationPlacement Options OverviewWall-Mount Option InstallationAccessing the Web-Based Utility Chapter Quick Configuration OverviewSetup WirelessSwitch AdministrationSystem Status Chapter Advanced Configuration Advanced ConfigurationSetup Wireless Wireless Basic SettingsWireless Site Survey WPA-Personal aka WPA-PSK Wireless Wireless SecurityWPA2-Personal WPA-EnterpriseWPA2-Enterprise Switch Wireless Advanced SettingsSwitch Port Management Switch Port Mirroring Switch VlanPort Mirroring Setting 802.1Q Port-Based Switch MAC Based ACLSwitch Spanning Tree Switch QoSSwitch MAC Table AdministrationAdministration Password Administration Web AccessAdministration Factory Defaults Administration SnmpSystem Status Wireless Status Administration Firmware UpgradeSystem Status System Status System StatusSystem Status Port Statistics Ad-HocPersonal, etc Wireless Security Checklist Appendix a Wireless Security ChecklistAppendix a General Network Security GuidelinesAppendix B Appendix B GlossaryGlossary Http HyperText Transport Protocol GlossarySnmp Simple Network Management Protocol a Smtp Simple Mail Transfer Protocol The standard eAppendix B Appendix C Specifications SpecificationsAppendix C Warranty Information Limited WarrantyAppendix D Regulatory Information Appendix EAvis d’Industrie Canada Wireless DisclaimerDansk Danish Miljøinformation for kunder i EU Appendix E Norsk Norwegian Miljøinformasjon for kunder i EU Appendix E Contact Information Appendix F
Related manuals
Manual 3 pages 10.7 Kb

WET200 specifications

The Linksys WET200 Wireless-G Ethernet Bridge is designed for businesses looking to extend their network capabilities without the hassle of running Ethernet cables throughout their premises. This high-performance device effectively connects wired devices to a wireless network, providing businesses with efficient access to internet resources and network shares.

One of the standout features of the WET200 is its dual-functionality. It operates as both an Ethernet bridge and a wireless access point, allowing users to connect multiple wired devices, such as printers, servers, or computers, to a wireless network. This flexibility makes it an excellent choice for environments where network mobility is crucial, such as offices, retail establishments, and warehouses.

Another key characteristic of the Linksys WET200 is its support for Wireless-G technology, offering a maximum wireless speed of up to 54 Mbps. This ensures that data transfer between connected devices is quick and reliable while providing adequate bandwidth for various applications, including file sharing and streaming. The device also adheres to the IEEE 802.11b/g standard, which means it is compatible with a vast number of other wireless devices.

The WET200 features a simple setup process, aided by its web-based configuration interface. This user-friendly interface allows for easy management of networking settings, making it accessible for both novice and experienced users. Security is a significant consideration, and the WET200 includes robust encryption protocols such as WEP, WPA, and WPA2 to protect data transmission over the wireless network.

Moreover, the Ethernet Bridge is equipped with two 10/100 Ethernet ports, enabling connections to multiple wired devices simultaneously. Its compact design allows for easy placement in various locations, and the inclusion of LEDs provides users with real-time feedback on connectivity status.

Overall, the Linksys WET200 Wireless-G Ethernet Bridge stands out with its combination of performance, flexibility, and ease of use, making it an invaluable asset for businesses aiming to expand their wired network capabilities without compromising on performance or security. It's a smart solution for those who need to harness the power of wireless connectivity while ensuring that their critical wired devices remain connected to the network efficiently.
Top Page Image Contents