Linksys WET200 manual Avis d’Industrie Canada, Wireless Disclaimer

Page 34

Appendix E

Regulatory Information

Avis d’Industrie Canada

Cet appareil numérique de la classe B est conforme aux normes NMB-003 et RSS210 du Canada.

L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :

1.il ne doit pas produire de brouillage et

2.il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Le dispositif a été conçupourfonctionneravecuneantenneayantungain maximum de 2 dBi. Les règlements d’Industrie Canada interdisent strictement l’utilisation d’antennes dont le gain est supérieur à cette limite. L’impédance requise de l’antenne est de 50 ohms.

Afin de réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour obtenir une communication satisfaisante.

Avis d’Industrie Canada concernant l’exposition aux radiofréquences :

Ce matériel est conforme aux limites établies par IC en matière d’exposition aux radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé et utilisé à une distance d’au moins 20 cm entre l’antenne et le corps de l’utilisateur.

L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur, ou fonctionner avec une autre antenne ou un autre émetteur.

Wireless Disclaimer

The maximum performance for wireless is derived from IEEE Standard 802.11 specifications. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and construction, operating system used, mix of wireless products used, interference and other adverse conditions.

Avis de non-responsabilité concernant les appareils sans fil

Les performances maximales pour les réseaux sans fil sont tirées des spécifications de la norme IEEE 802.11. Les performances réelles peuvent varier, notamment en fonction de la capacité du réseau sans fil, du débit de la transmission de données, de la portée et de la couverture. Les performances dépendent de facteurs, conditions et variables multiples, en particulier de la distance par rapport au point d’accès, du volume du trafic réseau, des matériaux utilisés dans le bâtiment et du type de construction, du système d’exploitation et de la combinaison de produits sans fil utilisés, des interférences et de toute autre condition défavorable.

Wireless-G Business Ethernet Bridge

30

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Wireless-G Business Ethernet Bridge Icon Descriptions About This GuideAbout This Guide Online ResourcesTable of Contents Appendix B Glossary Appendix a Wireless Security ChecklistAppendix E Regulatory Information Chapter Chapter IntroductionNetwork Topology Chapter Planning Your Wireless NetworkNetwork Layout Example of WET200 in Ad-Hoc Mode Front Panel Chapter Product OverviewProduct Overview Back PanelPlacement Options Chapter InstallationInstallation OverviewInstallation Wall-Mount OptionSetup Chapter Quick Configuration OverviewAccessing the Web-Based Utility WirelessAdministration SwitchSystem Status Advanced Configuration Chapter Advanced ConfigurationSetup Wireless Basic Settings WirelessWireless Site Survey Wireless Wireless Security WPA-Personal aka WPA-PSKWPA-Enterprise WPA2-PersonalWPA2-Enterprise Wireless Advanced Settings SwitchSwitch Port Management Switch Vlan Switch Port MirroringPort Mirroring Setting 802.1Q Switch MAC Based ACL Port-BasedSwitch QoS Switch Spanning TreeAdministration Password AdministrationSwitch MAC Table Administration Web AccessAdministration Snmp Administration Factory DefaultsSystem Status Administration Firmware UpgradeSystem Status Wireless Status System Status System StatusAd-Hoc System Status Port StatisticsPersonal, etc Appendix a Appendix a Wireless Security ChecklistWireless Security Checklist General Network Security GuidelinesAppendix B Glossary Appendix BGlossary Glossary Http HyperText Transport ProtocolSmtp Simple Mail Transfer Protocol The standard e Snmp Simple Network Management Protocol aAppendix B Specifications Appendix C SpecificationsAppendix C Limited Warranty Warranty InformationAppendix D Appendix E Regulatory InformationWireless Disclaimer Avis d’Industrie CanadaDansk Danish Miljøinformation for kunder i EU Appendix E Norsk Norwegian Miljøinformasjon for kunder i EU Appendix E Appendix F Contact Information
Related manuals
Manual 3 pages 10.7 Kb

WET200 specifications

The Linksys WET200 Wireless-G Ethernet Bridge is designed for businesses looking to extend their network capabilities without the hassle of running Ethernet cables throughout their premises. This high-performance device effectively connects wired devices to a wireless network, providing businesses with efficient access to internet resources and network shares.

One of the standout features of the WET200 is its dual-functionality. It operates as both an Ethernet bridge and a wireless access point, allowing users to connect multiple wired devices, such as printers, servers, or computers, to a wireless network. This flexibility makes it an excellent choice for environments where network mobility is crucial, such as offices, retail establishments, and warehouses.

Another key characteristic of the Linksys WET200 is its support for Wireless-G technology, offering a maximum wireless speed of up to 54 Mbps. This ensures that data transfer between connected devices is quick and reliable while providing adequate bandwidth for various applications, including file sharing and streaming. The device also adheres to the IEEE 802.11b/g standard, which means it is compatible with a vast number of other wireless devices.

The WET200 features a simple setup process, aided by its web-based configuration interface. This user-friendly interface allows for easy management of networking settings, making it accessible for both novice and experienced users. Security is a significant consideration, and the WET200 includes robust encryption protocols such as WEP, WPA, and WPA2 to protect data transmission over the wireless network.

Moreover, the Ethernet Bridge is equipped with two 10/100 Ethernet ports, enabling connections to multiple wired devices simultaneously. Its compact design allows for easy placement in various locations, and the inclusion of LEDs provides users with real-time feedback on connectivity status.

Overall, the Linksys WET200 Wireless-G Ethernet Bridge stands out with its combination of performance, flexibility, and ease of use, making it an invaluable asset for businesses aiming to expand their wired network capabilities without compromising on performance or security. It's a smart solution for those who need to harness the power of wireless connectivity while ensuring that their critical wired devices remain connected to the network efficiently.
Top Page Image Contents