Linksys WRT51AB manual To start over, I need to set the Router to factory default

Page 41

Instant Wireless® Series

10.I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop- up window.

If you have proxy settings, you need to disable these on your computer. Because the Router is the gateway for the Internet connection, the computer does not need any proxy settings to gain access. Please follow these directions to verify that you do not have any proxy settings and that the browser you use is set to connect directly to the LAN.

For Microsoft Internet Explorer 5.0 or higher:

A.Click Start, Settings, and Control Panel. Double-clickInternet Options.

B.Click the Connections tab.

C.Click the LAN settings button and remove anything that is checked.

D.Click the OK button to go back to the previous screen.

E.Click the option Never dial a connection. This will remove any dial-up pop-ups for PPPoE users.

For Netscape 4.7 or higher:

A. Start Netscape Navigator, and click Edit, Preferences, Advanced, and Proxies.

B.Make sure you have Direct connection to the Internet selected on this screen.

C.Close all the windows to finish.

11. To start over, I need to set the Router to factory default.

Hold the Reset button for 10 seconds and then release it. This will return the password, forwarding, and other settings on the Router to the factory default settings. In other words, the Router will revert to its original factory configu- ration.

12. I need to upgrade the firmware.

In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download the latest firmware at www.linksys.com. Follow these steps:

A.Go to the Linksys website at http://www.linksys.com and download the latest firmware.

B.To upgrade the firmware, follow the steps in the Help section found in “Chapter 6: The Router’s Web-based Utility.”

Dual-Band Wireless A+B Broadband Router

13. The firmware upgrade failed, and/or the Diag LED is flashing.

The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or make the Diag LED stop flashing:

A.If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware). Open the pdf that was downloaded along with the firmware and TFTP program, and follow the pdf’s instructions.

B.Set a static IP address on the PC; refer to “Problem #1, I need to set a stat- ic IP address.” Use the following IP address settings for the computer you are using:

IP Address: 192.168.1.50

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

C.Perform the upgrade using the TFTP program or the Router’s web-based utility through its Help tab.

14. My DSL service’s PPPoE is always disconnecting.

PPPoE is not actually a dedicated or always-on connection. The DSL ISP can disconnect the service after a period of inactivity, just like a normal phone dial- up connection to the Internet. There is a setup option to “keep alive” the con- nection. This may not always work, so you may need to re-establish connec- tion periodically.

A. To connect to the Router, go to the web browser, and enter http://192.168.1.1 or the IP address of the Router.

B.Enter the password, if asked. (The default password is admin.)

C.On the Setup screen, select the option Keep Alive, and set the Redial Period option at 20 (seconds).

D.Click the Apply button.

E.Click the Status tab, and click the Connect button.

F.You may see the login status display as Connecting. Press the F5 key to refresh the screen, until you see the login status display as Connected.

G.Click the Apply button to continue.

If the connection is lost again, follow steps E to G to re-establish connection.

74

75

Image 41
Contents Dual-Band Wireless A+B Broadband Router Copyright & Trademarks Table of Contents Environmental 127 Common Problems and Solutions Frequently Asked QuestionsIntroduction Router’s Functions FeaturesIP Addresses What’s an IP Address?Dynamic IP Addresses Dhcp Dynamic Host Configuration Protocol ServersRouter Setup Overview Router’s Front Panel LEDs Getting to Know the Dual-Band Wireless A+B Broadband RouterRouter’s Back Panel Proceed to Connect the Router LAN IndicatorsInternet Indicators Overview Wired Connection to a PCConnect the Router Wireless Connection to a PC Configure the PCsGo to Configure the Router’s Basic Settings Configuring Windows 98 and Millennium PCsConfiguring Windows 2000 PCs Configuring Windows XP PCs Configure the Router’s Basic Settings Enter the Default Gateway Automatic Configuration DhcpStatic or Fixed IP Address Enter the Internet IP AddressRouter’s Web-based Utility How to Access the Web-based UtilitySetup Automatic Configuration DhcpStatic IP Pptp 5GHz, 802.11a 5GHz, 802.11a WEP 4GHz, 802.11b WEP Status PasswordLAN Dhcp Help LogAdvanced Tabs 5GHz, 802.11a Advanced Wireless802.1x Configuration Radius Server Filters 11-20 , 21-30 , 31-40 , or 41-50 from Private MAC Filter To set up a filterPrivate IP Filter Port Forwarding Applications External Port TCP Protocol UDP ProtocolClick the Delete This Entry button RoutingDMZ Host MAC Address Clone Common Problems and Solutions Appendix a TroubleshootingNeed to set a static IP address on a PC For Windows NTFor Windows 98, Me, 2000, and XP For Windows XPWant to test my Internet connection TCP UDP Need to set up a server behind my RouterCan’t get the Internet game, server, or application to work Need to upgrade the firmware To start over, I need to set the Router to factory defaultFirmware upgrade failed, and/or the Diag LED is flashing My DSL service’s PPPoE is always disconnectingClick the Advanced = Filters tab Frequently Asked QuestionsHow can I block corrupted FTP downloads? Does the Router support ICQ send file?What are the advanced features of the Router? What is DMZ Hosting?What is the Ieee 802.11a standard? What is the Ieee 802.11b standard?What is ad-hoc mode? What Ieee 802.11b features are supported?What is infrastructure mode? What is roaming?What is a MAC Address? What is WEP?How do I reset the Router? How do I resolve issues with signal loss?Step One Pinging an IP Address Appendix B How to Ping Your ISP’s E-mail & Web AddressesBackground Appendix C Configuring Wireless SecurityStep Two Pinging for a Web Address WEP Encryption 802.1x AuthenticationFigure C-2 MD5 Authentication for Windows XPFigure C-5 Figure C-9 Digital Certificate InstallationFigure C-13 Click Install this certificateFigure C-18 TLS Authentication for Windows XPFigure C-21 For Windows 95, 98, and Me Figure C-25For Windows NT, 2000, and XP Figure D-3Appendix E Glossary 111 113 115 117 119 121 123 125 One 10/100 RJ-45 Port for Cable/DSL Modem Appendix F SpecificationsCategory 5 Ethernet Network Cable or better EnvironmentalSales Information Technical Support RMA Issues Fax Appendix G Warranty InformationAppendix H Contact Information Web site FTP siteCopyright 2002 Linksys, All Rights Reserved