Linksys BEFSX41 manual Tunnel 2 router-win

Page 58

Instant Broadband® SeriesEtherFast® Cable/DSL Firewall Router with 4-Port Switch/VPN Endpoint

7. Select

the

Tunnel

Tunnel 2: router->win

Setting tab, shown

in

 

Figure C-16, and click

9. In the screen, shown in

The tunnel endpoint is

Figure C-18, make sure

specified

by

this

IP

that “win -> router” is

Address

radio

button.

select and deselect the

Then, enter the Router’s

Use Add Wizard

WAN IP Address.

 

check box. Then, click

the Add button to cre- ate the second IP filter.

 

Figure C-16

8. Select the Connection

Figure C-18

 

Type tab, as shown in

10. Go to the IP Filter List

Figure C-17, and click

tab, and click the filter

All network connec-

list router->win, as

tions. Then, click the OK

shown in Figure C-19

or Close button to finish

 

this rule.

 

Figure C-17

Figure C-19

108

109

Page 57 Page 59
Image 58
Page 57 Page 59
Contents User Guide Copyright & Trademarks Table of Contents Introduction FeaturesEnvironmental 139 An Introduction to LANs and WANs IP AddressesWhy Do I Need a VPN? Network Setup OverviewYour Virtual Private Network VPN What is a Virtual Private Network? Firewall Router to Firewall RouterModem connection will not work from any other port PowerRouter’s Back Panel PortsRouter’s Front Panel LEDs WAN and LAN LEDsProceed to Connect the Router Connect the Router Connecting Your Hardware Together and Booting UpRouter’s hardware installation is now complete OverviewConfigure the PCs Configuring Windows 95, 98, and Millennium PCsGo to Configure the Router Configuring Windows 2000 PCsConfiguring Windows XP PCs Configure the Router Advanced Proxies. Click Direct Connection to the Internet Obtain an IP Address AutomaticallyStatic IP Address Enter the Gateway AddressPPPoE RASQuick and Easy Router Administration Cable/DSL Firewall Router’s Web-based UtilitySetup User Name and Password Static IPWAN IP Firewall Multicast Pass Through Remote UpgradeBlock WAN Request IPSec Pass ThroughEstablishing a Tunnel VPNLocal Secure Group and Remote Secure Group Remote Security Gateway Encryption AuthenticationKey Management Instant Broadband Series Advanced Settings for Selected IPSec Tunnel PhaseOther Settings PasswordStatus Dhcp Log Help Advanced FiltersInstant Broadband Series Forwarding UPnP Forwarding Port Triggering Dynamic Routing Static RoutingDMZ Port DMZ HostDMZ Host Address Current DMZ Host MAC Address CloneDynDNS.org DdnsCommon Problems and Solutions Appendix a TroubleshootingTZO.com For Windows XP For Windows NTFor Windows 95, 98, and Me For Windows XP Am not able to access the Router’s web interface Setup Can’t get the Internet game, server, or application to work To start over, I need to set the Router to factory default Click the Advanced = Filter tab Need to use port triggeringFrequently Asked Questions TCP/IP is compatible with the Router Appendix B Maximizing VPN Security Windows 2000 or Windows XP IntroductionEnvironment Step One Create an IPSec PolicyStep Two Build Filter Lists Filter List 1 win-routerIP Address Filter List 2 router=win Figure C-6Step Three Configure Individual Tunnel Rules Tunnel 1 win-routerShared key, as shown Respond Using IPSec XYZ12345. ClickString to Protect Negotiate Security Key exchange pre AcceptTunnel 2 router-win Preshared key, Action Require Security This string to protectKey Exchange XYZ12345Figure C-24 Step Four Assign New IPSec PolicyStep Five Create a Tunnel Through the Web-based Utility Figure C-28Appendix E How to Ping Your ISP’s E-mail & Web Addresses Appendix D Snmp FunctionsFigure E-1 Appendix F Installing the TCP/IP Protocol TCP/IP installation is now completeFigure G-1 For Windows NT, 2000, and XPFigure G-5 Appendix H Glossary 129 131 133 135 137 Appendix I Specifications EnvironmentalSales Information Appendix J Warranty InformationAppendix K Contact Information Web FTP SiteCopyright 2003 Linksys, All Rights Reserved
Top Page Image Contents