NETGEAR CG814M manual Log in to the Gateway, Connecting the Power Adapter

Page 28

Reference Manual for the Model CG814M Wireless Cable Modem Gateway

Connecting the Power Adapter

To connect the power adapter to the gateway:

1.Plug the connector of the power adapter into outlet on the rear panel of the modem.

2.Plug the other end of the adapter into an AC power outlet.

3.Verify that the PWR LED on the modem is lit.

After applying power to the gateway, complete the following steps to verify that power is correctly applied:

1.When power is first applied, verify that the Power LED comes on. All the numbered LAN LEDs will be briefly tested.

2.After approximately 10 seconds, verify that the local Ethernet or USB port LED is lit for the port that is connected to your computer.

If a port’s LED is lit, a link has been established to the connected device. If a local Ethernet port is connected to a 100 Mbps device, verify that the port’s LED is green. If the port is 10 Mbps, the LED should be yellow.

Log in to the Gateway

Note: To connect to the gateway, your computer needs to be configured to obtain an IP address automatically via DHCP. Please refer to Appendix C, "Preparing Your Network" for instructions on how to do this.

1.Turn on the gateway.

2.Now, turn on your computer.

Note: If you usually run software to log in to your Internet connection, do not run that software.

2-8

Connecting the Gateway to the Internet

Image 28
Contents NETGEAR, Inc Trademarks World Wide Web Page Contents USB Appendix a Appendix C Contents Contents Audience About This ManualTypographical Conventions Special Message Formats Technical SupportKey Features Chapter IntroductionAbout the CG814M Gateway Built-in Cable ModemContent Filtering Powerful, True Firewall802.11b Standards-based Wireless Networking USB Port Configurable Auto Uplink Ethernet ConnectionProtocol Support Easy Installation and Management What’s in the Box? Firewall’s Front PanelLED Descriptions Gateway’s Rear Panel CG814M Gateway Rear PanelIntroduction Connecting the Gateway to the Internet What You Will Need Before You BeginLAN Hardware Requirements Computer RequirementsInternet Configuration Requirements LAN Configuration RequirementsWhere Do I Get the Internet Configuration Parameters? Connecting the Gateway to the Internet Record Your Internet Connection Information Connecting the CG814M Gateway Connecting to Your ComputerEthernet USBConnecting to your Cable Service Provider WirelessConnecting the Power Adapter Log in to the GatewayLogin window opens as shown in -3below Connect to the Internet Connecting the CG814M Gateway to the Internet ConfigurationConnecting the Gateway to the Internet Connecting the Gateway to the Internet Connecting the Gateway to the Internet Considerations For a Wireless Network Chapter Wireless ConfigurationSecurity Wireless Settings Placement and RangeWireless Settings Restricting Wireless Access by MAC AddressConfiguring Wired Equivalent Privacy WEP Wireless Configuration Wireless Configuration Changing the Built-In Password Protecting Access to Your CG814M GatewayChapter Protecting Your Network Blocking Keywords, Sites, and Services Set Password menuBlock Keywords and Domains Click on the Block Sites link of the Content Filtering menu Blocking Services ProxyPort Blocking CookiesPort Forwarding Port Blocking menuTo forward inbound traffic Port Triggering Considerations for Port ForwardingTo configure Port Triggering Setting Up a Default DMZ Host Respond to Ping on Internet WAN PortProtecting Your Network Chapter Managing Your Network Network Status InformationViewing Gateway Status This screen shows the following parametersMenu 3.2 Router Status Fields Connection Status Connection screenLAN IP Setup Configuring LAN IP SettingsCurrent System Time Dhcp Use router as Dhcp serverViewing and Emailing Logged Information Logs menuErasing Configuration Enabling Logs Event E-mail NotificationRunning Diagnostic Utilities Diagnostics menuManaging Your Network Chapter Troubleshooting Basic FunctionsTest LED Stays On Power LED Not OnLocal Link LEDs Not On Troubleshooting the Web Configuration Interface Cable Link LED Not OnTroubleshooting a TCP/IP Network Using a Ping Utility Troubleshooting the ISP ConnectionTesting the LAN Path to Your Gateway Testing the Path from Your PC to a Remote Device Troubleshooting Appendix a Technical Specifications TCP/IPTechnical Specifications Appendix B Networks, Routing, and Firewall Basics Related Publications Basic Router ConceptsRouting Information Protocol What is a Router?IP Addresses and the Internet Three Main Address Classes Netmask EqualsSubnet Addressing Example of Subnetting a Class B AddressNetmask Notation Translation Table for One Octet Private IP Addresses Single IP Address Operation Using NAT Single IP Address Operation Using NATMAC Addresses and Address Resolution Protocol Related DocumentsInternet Security and Firewalls IP Configuration by DhcpDomain Name Server Denial of Service Attack What is a Firewall?Stateful Packet Inspection Wireless Networking Wireless Network ConfigurationAd-hoc Mode Peer-to-Peer Workgroup Infrastructure ModeExtended Service Set Identification Essid Authentication and WEP EncryptionWireless Channel Selection Table B-1 802.11b Radio Frequency ChannelsUplink Switches and Crossover Cables Ethernet CablingCable Quality Appendix C Preparing Your Network Preparing Your Computers for TCP/IP NetworkingConfiguring Windows 95, 98, and ME for TCP/IP Networking Install or Verify Windows Networking ComponentsPreparing Your Network Enabling Dhcp to Automatically Configure TCP/IP Settings Selecting Windows’ Internet Access MethodConfiguring Windows NT, 2000 or XP for IP Networking Verifying TCP/IP PropertiesConfiguring the Macintosh for TCP/IP Networking MacOS 8.6 orMacOS Verifying TCP/IP Properties for Macintosh Computers What Is Your Configuration Information? Verifying the Readiness of Your Internet AccountMail.xxx.yyy.com Preparing Your Network Restarting the Network Glossary Networks See Network Address Translation Connection