NETGEAR CG814M manual Ethernet, Usb

Page 26

Reference Manual for the Model CG814M Wireless Cable Modem Gateway

Ethernet

To connect your computer to the modem via Ethernet:

1.Locate the Category 5 Ethernet cable which came with your modem.

2.Connect your computer to the modem using the Ethernet cable.:

Note: Note: The CG814M Gateway incorporates Auto UplinkTM technology. Each LOCAL Ethernet port will automatically sense whether the cable plugged into the port should have a 'normal' connection (e.g. connecting to a PC) or an 'uplink' connection (e.g. connecting to a switch or hub). That port will then configure itself to the correct configuration. This feature also eliminates the need to worry about crossover cables, as Auto Uplink will accommodate either type of cable to make the right connection.

USB

To connect your computer to the modem via USB involves installing the USB driver:

Note: The USB connection option is only available for Windows PCs. Also, Windows 95 does not support USB without special operating system upgrades and patches.

1.Install the USB driver

a.Insert the CD which came with your modem into the CD drive of your computer.

a.Connect the USB cable to your modem and plug in the AC power for the modem.

b.Use the USB cable to connect your computer to the modem.

2-6

Connecting the Gateway to the Internet

Image 26
Contents NETGEAR, Inc Trademarks World Wide Web Page Contents USB Appendix a Appendix C Contents Contents Typographical Conventions About This ManualAudience Special Message Formats Technical SupportAbout the CG814M Gateway Key FeaturesChapter Introduction Built-in Cable Modem802.11b Standards-based Wireless Networking Powerful, True FirewallContent Filtering Protocol Support Configurable Auto Uplink Ethernet ConnectionUSB Port Easy Installation and Management What’s in the Box? Firewall’s Front PanelLED Descriptions Gateway’s Rear Panel CG814M Gateway Rear PanelIntroduction LAN Hardware Requirements Connecting the Gateway to the InternetWhat You Will Need Before You Begin Computer RequirementsWhere Do I Get the Internet Configuration Parameters? LAN Configuration RequirementsInternet Configuration Requirements Connecting the Gateway to the Internet Record Your Internet Connection Information Connecting the CG814M Gateway Connecting to Your ComputerEthernet USBConnecting to your Cable Service Provider WirelessConnecting the Power Adapter Log in to the GatewayLogin window opens as shown in -3below Connect to the Internet Connecting the CG814M Gateway to the Internet ConfigurationConnecting the Gateway to the Internet Connecting the Gateway to the Internet Connecting the Gateway to the Internet Security Chapter Wireless ConfigurationConsiderations For a Wireless Network Wireless Settings Placement and RangeWireless Settings Restricting Wireless Access by MAC AddressConfiguring Wired Equivalent Privacy WEP Wireless Configuration Wireless Configuration Chapter Protecting Your Network Protecting Access to Your CG814M GatewayChanging the Built-In Password Blocking Keywords, Sites, and Services Set Password menuBlock Keywords and Domains Click on the Block Sites link of the Content Filtering menu Blocking Services ProxyPort Blocking CookiesPort Forwarding Port Blocking menuTo forward inbound traffic Port Triggering Considerations for Port ForwardingTo configure Port Triggering Setting Up a Default DMZ Host Respond to Ping on Internet WAN PortProtecting Your Network Chapter Managing Your Network Network Status InformationViewing Gateway Status This screen shows the following parametersMenu 3.2 Router Status Fields Connection Status Connection screenCurrent System Time Configuring LAN IP SettingsLAN IP Setup Dhcp Use router as Dhcp serverViewing and Emailing Logged Information Logs menuErasing Configuration Enabling Logs Event E-mail NotificationRunning Diagnostic Utilities Diagnostics menuManaging Your Network Chapter Troubleshooting Basic FunctionsLocal Link LEDs Not On Power LED Not OnTest LED Stays On Troubleshooting the Web Configuration Interface Cable Link LED Not OnTesting the LAN Path to Your Gateway Troubleshooting the ISP ConnectionTroubleshooting a TCP/IP Network Using a Ping Utility Testing the Path from Your PC to a Remote Device Troubleshooting Appendix a Technical Specifications TCP/IPTechnical Specifications Appendix B Networks, Routing, and Firewall Basics Related Publications Basic Router ConceptsIP Addresses and the Internet What is a Router?Routing Information Protocol Three Main Address Classes Netmask EqualsSubnet Addressing Example of Subnetting a Class B AddressNetmask Notation Translation Table for One Octet Private IP Addresses Single IP Address Operation Using NAT Single IP Address Operation Using NATMAC Addresses and Address Resolution Protocol Related DocumentsDomain Name Server IP Configuration by DhcpInternet Security and Firewalls Stateful Packet Inspection What is a Firewall?Denial of Service Attack Ad-hoc Mode Peer-to-Peer Workgroup Wireless NetworkingWireless Network Configuration Infrastructure ModeExtended Service Set Identification Essid Authentication and WEP EncryptionWireless Channel Selection Table B-1 802.11b Radio Frequency ChannelsUplink Switches and Crossover Cables Ethernet CablingCable Quality Appendix C Preparing Your Network Preparing Your Computers for TCP/IP NetworkingConfiguring Windows 95, 98, and ME for TCP/IP Networking Install or Verify Windows Networking ComponentsPreparing Your Network Enabling Dhcp to Automatically Configure TCP/IP Settings Selecting Windows’ Internet Access MethodConfiguring Windows NT, 2000 or XP for IP Networking Verifying TCP/IP PropertiesConfiguring the Macintosh for TCP/IP Networking MacOS 8.6 orMacOS Verifying TCP/IP Properties for Macintosh Computers What Is Your Configuration Information? Verifying the Readiness of Your Internet AccountMail.xxx.yyy.com Preparing Your Network Restarting the Network Glossary Networks See Network Address Translation Connection