Actiontec electronic GT704WR Regulatory Compliance Notices, Modifications, Class B Equipment

Page 110

Notices

Regulatory Compliance Notices

Class B Equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter- ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by implementing one or more of the following measures:

sReorient or relocate the receiving antenna;

sIncrease the separation between the equipment and receiver;

sConnect the equipment to an outlet on a circuit different from that to which the receiver is connected;

sConsult the dealer or an experienced radio or television technician for help.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Actiontec Electronics, Inc., may void the user’s authority to operate the equipment.

Declaration of conformity for products marked with the FCC logo – United States only.

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions:

1. This device may not cause harmful interference;

107

Image 110

Contents Wireless Cable/DSL Router Table of Contents Setting Up Static IP on the Computer Setting Up a NetworkTroubleshooting SpecificationsPackage Contents Introduction1Features Minimum System RequirementsPower Light Getting to Know the RouterEthernet Lights Wireless LightInternet Light Ethernet PortsPower port is used to connect the Power cord to the Router Reset SwitchPower Port Cable/DSL PortThis page left intentionally blank Setting Up Router Connecting a Computer to the RouterPage Setting Up the Router Page Setting Up the Router Page Setting Up the Router Page Setting Up the Router Page Setting Up the Router Page Installation Buddy checks the configuration of the Router This page left intentionally blank To configure the Router for basic operation Performing a Basic SetupBasic Setup Page Performing a Basic Setup Changing the Admin User Name and Password Click Save and Restart at the bottom of the screenPerforming a Basic Setup This page left intentionally blank To access the Advanced Setup configuration screens Using Advanced SetupAccessing Advanced Setup Page WAN IP Address Dialout on-demand/Idle timeout Obtain an IP Through DhcpUsing Advanced Setup Wireless Settings ChannelOff WEPWEP+802.1x Wireless MAC Authentication WPAWireless Advanced Settings LAN IP Address Dhcp ServerBeginning IP Address Ending IP AddressDNS Server Services BlockingDNS Dynamic or Static Website Blocking Remote Management Port Forwarding DMZ Hosting Firewall Dynamic RoutingStatic Routing UPnP Universal Plug and PlayMAC Address Cloning Viewing Router’s Settings StatusPage Routing Table WAN StatusLAN Status Active User ListUsing Utilities Web Activity LogRestore Default Settings Upgrade Firmware This page left intentionally blank Setting Up a Network EthernetPage Setting Up a Network Page Setting Up a Network Wireless Setting Up a Network This page left intentionally blank Using on Network With Another Router/Gateway TroubleshootingTroubleshooting Physical ConnectionsFrequently Asked Questions Will cordless phones interfere with the Router? Which wireless cards will work with the Router?Do I need a specific cable or DSL modem to use the Router? Network What is the valid IP range I can use for my home network?How do I find out which IP address my computer is using? Yes, if the application is designed to run over a network Connections What is WEP?What is the default username for the Router? How many computers can be connected through the Router?How do I make a HEX-based WEP key? What is WPA?What is NAT and how does it protect my network? Does the Router function as a firewall?This page left intentionally blank Reference Locating Computer InformationLocating Windows Operating System Files Appendix a Reference Click Search Setting Up Static IP On the Computer Windows 98 SEPage 192.168.0.2 Windows Me Enter the following address in the Subnet mask text boxAppendix B Setting Up Static IP on the Computer 192.168.0.2 Windows Page Appendix B Setting Up Static IP on the Computer 192.168.0.2 Windows XP Page Appendix B Setting Up Static IP on the Computer Enter the following address in the IP Address text box Comparing Broadband Service with a Dial-Up Modem Computer SecurityInternet Browsers Router SecurityComputer Security Electronic Security This page left intentionally blank Specifications D GeneralPower, Internet, Wireless, Ethernet Wireless Operating RangeLED Indicators EnvironmentalAccess Point GlossaryPage Ssid This page left intentionally blank Firewall Security Level Services Table High Security LevelMedium Security Level Low Security LevelService Acronym Definitions Basic Security Level323 Real audio/videoIcmp 120Non-Windows G System Setup Classic104 Appendix G Non-Windows Setup 106 Class B Equipment Regulatory Compliance NoticesModifications Miscellaneous Legal Notices All other names are the property of their respective ownersLimited Warranty 109110 Limited Warranty 112