Advantech PCM-3362 user manual Express Installation, Manual Installation

Page 49

\Demo

„

SusiDemo.EXE

 

Demo program on Windows XP.

 

„

Susi.dll

 

Dynamic library for SUSI on Windows XP.

\Demo\SRC

Source code of the demo program on Windows XP.

The following section illustrates the installation process.

Note! The version of the SUSI Library Installer shown on each screen shot below depends on your own particular version.

1.Extract Susi.zip.

2.Double-click the "Setup.exe" file.

The installer searches for a previous installation of the SUSI Library. If it locates one, a screen shot opens asking whether you want to modify, repair or remove the soft- ware. If a previous version is located, please see the section of [Maintenance Setup]. If it is not located, the following screen shot opens. Click Next.

4.3.4.2Windows CE

In windows CE, there are three ways to install the SUSI Library, you can install it manually or use Advantech CE-Builder to install the library or just copy the programs and the library onto a compact flash card.

Express Installation:

You can use Advantech CE-Builder to load the library into the image.

„First, you click the My Component tab.

„In this tab, you click Add New Category button to add a new category, e.g. the SUSI Library.

„Then you can add a new file in this category, and upload the SUSI.dll for this category.

„After these steps, you can select the SUSI Library category you created for every project.

Manual Installation:

You can add the SUSI Library into the image by editing any bib file.

First you open project.bib in the platform builder.

„Add this line to the MODULES section of project.bib Susi.dll $(_FLATRELEASEDIR)\Susi.dll NK SH

„If you want to run the window-based demo, add following line: SusiTest.exe $(_FLATRELEASEDIR)\SusiTest.exe

„If you want to run the console-based demo, add following lines: Watchdog.exe $(_FLATRELEASEDIR)\Watchdog.exe NK S GPIO.exe $(_FLATRELEASEDIR)\GPIO.exe NK S SMBUS.exe $(_FLATRELEASEDIR)\SMBUS.exe NK S

„Place the three files into any files directory.

„Build your new Windows CE operating system.

Chapter 4 Software Introduction & Installation

41

PCM-3362 User Manual

Image 49
Contents PCM-3362 Copyright Acknowledgements Additional Information and Assistance Packing ListDeclaration of Conformity FCC Class a Contents AMI Bios Setup Appendix B Appendix aAppendix C Appendix D Watchdog Timer and Gpio sample General Information ChapterSpecifications FeaturesIntroduction Standard PC/104-plus Biscuit SBC FunctionsEthernet Interface 2 VGA/LVDS InterfaceOS support Mechanical and EnvironmentalBoard layout Dimensions Component Side Board layout dimensionsBoard layout Dimensions Solder Side Page Hardware Installation Jumpers ConnectorsConnectors solder side Connectors component sideBlock diagram Setting JumpersClear Cmos JP1 Lvds Panel Power Select JP2Open Closed Flash Installing SODIMMs3 COM3 RS422/RS485 Select JP3 PCI I/O Voltage Select JP4Front Panel Connector CN12 USB connectors CN9 & CN10High Definition Audio Interface CN1 VGA/LCD interface connectionsSata Connector CN15 Buzzer Connector CN13COM port connector CN16 & CN17 Giga LAN Connector CN18ATX Power in connector CN23 Gpio Connector CN21Power Connectors CN24 19 I2C Bus connector CN25Page AMI Bios Setup Main Setup Entering SetupSystem time / System date Advanced Bios Features SetupExecute-Disable Bit Capability CPU ConfigurationHyper Threading Technology Intel SpeedStepTM techIDE Configuration Hardware Health Configuration Super I/O ConfigurationSerial Port1 / Port2 / Port3 IRQ Auto Direction Control SelTemperature & Voltage show Acpi SettingsReport Video on S3 Resume Acpi Apic support Headless modeAMI Oemb table Energy Lake Feature Ahci ConfigurationHigh Performance Event Timer USB Device Wakeup From S3/S4APM Configuration MPS Configuration Event Log ConfigurationMark all events as read Clear Event LogUSB Configuration Smbios ConfigurationUSB 2.0 Controller Mode Bios Ehci Hand-Off Advanced PCI/PnP SettingsHotplug USB FDD Support Emulation TypePlug & Play O/S PCI Latency TimerAllocate IRQ to PCI VGA Palette SnoopingBoot settings Configuration Boot SettingsQuiet Boot AddOn ROM Display ModeSecurity Setup North Bridge Chipset Configuration Advanced Chipset SettingsConfigure Dram Timing by SPD Memory HoleBoot Display Device South Bridge Chipset ConfigurationDVMT/FIXED Memory Flat Panel TypeSave Changes and Exit Exit OptionLoad Fail-Safe Defaults Load Optimal DefaultsDiscard Changes and Exit Software Introduction & Installation Value-Added Software Services Driver InstallationS/W Introduction Gpio API Software APIsSusi Utilities Susi InstallationSusi.lib Susi.dllManual Installation Express InstallationSusi Sample Programs Windows Graphics ModeSample Programs SusiDemo.exeSoftware Introduction & Installation SMBus I2CSoftware Introduction & Installation Watchdog Display ControlHardware Monitor Page Chipset Software Installation Utility Before You Begin Windows XP/Vista/Win7 Driver SetupIntegrated Graphic Device Setup Windows XP/ Vista /Win7 Driver Setup LAN Configuration Installation Pin Assignments Appendix aJP1 Clear Cmos Jumper and Connector TablesAppendix a Pin Assignments CN7 CN9 6 8CN12 Front panel Connector Part Number CN16 COM1~COM2 Connector Part Number 6 8 CN21 Gpio Connector Part Number CN25 I2C BUS connector Part Number System Assignments Appendix B1st MB Memory Map System I/O PortsDMA channel assignments Table B.4 Interrupt assignments Interrupt assignmentsPage Mechanical Drawings Appendix CFigure C.1 PCM-3362 Mechanical Drawing Component Side Board Mechanical DrawingsAppendix C Mechanical Drawings Figure C.3 PCM-3362N Heatsink Mechanical Drawing Heatsink Mechanical DrawingsFigure C.5 PCM-3362 optional Heatspreader Mechanical Drawing Optional Heat spreader Mechanical DrawingsPage Appendix D Watchdog Timer and Gpio sample codeBit 10=Reserved Bit 62Reserve=00000 Watchdog Timer sample codeGpio sample code Appendix D Watchdog Timer and Gpio sample codePage Appendix D Watchdog Timer and Gpio sample code