Advantech PCM-3362 Plug & Play O/S, PCI Latency Timer, Allocate IRQ to PCI VGA, Palette Snooping

Page 38

Figure 3.19 PCI/PNP Setup (top)

Clear NVRAM

Set this value to force the BIOS to clear the Non-Volatile Random Access Memory (NVRAM).The Optimal and Fail-Safe default setting is No.

Plug & Play O/S

When set to No, BIOS configures all the device in the system. When set to Yes and if you install a Plug and Play operating system, the operating system configures the Plug and Play device not required for boot.

PCI Latency Timer

Value in units of PCI clocks for PCI device latency timer register.

Allocate IRQ to PCI VGA

When set to Yes will assigns IRQ to PCI VGA card if card requests IRQ. When set to No will not assign IRQ to PCI VGA card even if card requests an IRQ.

Palette Snooping

This item is designed to solve problems caused by some non-standard VGA card.

PCI IDE BusMaster

When set to enabled BIOS uses PCI busmastering for reading/writing to IDE drives.

OffBoard PCI/ISA IDE Card

Some PCI IDE cards may require this to be set to the PCI slot number that is holding the card. When set to Auto will works for most PCI IDE cards.

IRQ3 / 4 / 5 / 7 / 9 / 10 /11

This item allows you respectively assign an interruptive type for IRQ-3, 4, 5, 7, 9, 10, 11.

DMA Channel0 / 1 / 3 / 5 / 6 / 7

When set to Available will specified DMA is available to be used by PCI/PnP devices. When set to Reserved will specified DMA will Reserved for use by legacy ISA devices.

Reserved Memory Size

This item allows you to reserved size of memory block for legacy ISA device.

PCM-3362 User Manual

30

Image 38

Contents PCM-3362 Copyright Acknowledgements Declaration of Conformity Packing ListAdditional Information and Assistance FCC Class a Contents AMI Bios Setup Appendix C Appendix aAppendix B Appendix D Watchdog Timer and Gpio sample Chapter General InformationIntroduction FeaturesSpecifications Standard PC/104-plus Biscuit SBC FunctionsOS support 2 VGA/LVDS InterfaceEthernet Interface Mechanical and EnvironmentalBoard layout dimensions Board layout Dimensions Component SideBoard layout Dimensions Solder Side Page Hardware Installation Connectors JumpersConnectors component side Connectors solder sideSetting Jumpers Block diagramOpen Closed Lvds Panel Power Select JP2Clear Cmos JP1 3 COM3 RS422/RS485 Select JP3 Installing SODIMMsFlash PCI I/O Voltage Select JP4High Definition Audio Interface CN1 USB connectors CN9 & CN10Front Panel Connector CN12 VGA/LCD interface connectionsCOM port connector CN16 & CN17 Buzzer Connector CN13Sata Connector CN15 Giga LAN Connector CN18Power Connectors CN24 Gpio Connector CN21ATX Power in connector CN23 19 I2C Bus connector CN25Page AMI Bios Setup Entering Setup Main SetupAdvanced Bios Features Setup System time / System dateHyper Threading Technology CPU ConfigurationExecute-Disable Bit Capability Intel SpeedStepTM techIDE Configuration Serial Port1 / Port2 / Port3 IRQ Super I/O ConfigurationHardware Health Configuration Auto Direction Control SelReport Video on S3 Resume Acpi SettingsTemperature & Voltage show AMI Oemb table Headless modeAcpi Apic support High Performance Event Timer Ahci ConfigurationEnergy Lake Feature USB Device Wakeup From S3/S4APM Configuration Mark all events as read Event Log ConfigurationMPS Configuration Clear Event LogUSB 2.0 Controller Mode Smbios ConfigurationUSB Configuration Hotplug USB FDD Support Advanced PCI/PnP SettingsBios Ehci Hand-Off Emulation TypeAllocate IRQ to PCI VGA PCI Latency TimerPlug & Play O/S Palette SnoopingQuiet Boot Boot SettingsBoot settings Configuration AddOn ROM Display ModeSecurity Setup Configure Dram Timing by SPD Advanced Chipset SettingsNorth Bridge Chipset Configuration Memory HoleDVMT/FIXED Memory South Bridge Chipset ConfigurationBoot Display Device Flat Panel TypeExit Option Save Changes and ExitDiscard Changes and Exit Load Optimal DefaultsLoad Fail-Safe Defaults Software Introduction & Installation S/W Introduction Driver InstallationValue-Added Software Services Software APIs Gpio APISusi.lib Susi InstallationSusi Utilities Susi.dllExpress Installation Manual InstallationSample Programs Windows Graphics ModeSusi Sample Programs SusiDemo.exeSoftware Introduction & Installation I2C SMBusSoftware Introduction & Installation Display Control WatchdogHardware Monitor Page Chipset Software Installation Utility Windows XP/Vista/Win7 Driver Setup Before You BeginIntegrated Graphic Device Setup Windows XP/ Vista /Win7 Driver Setup LAN Configuration Installation Appendix a Pin AssignmentsJumper and Connector Tables JP1 Clear CmosAppendix a Pin Assignments CN7 6 8 CN9CN12 Front panel Connector Part Number CN16 COM1~COM2 Connector Part Number 6 8 CN21 Gpio Connector Part Number CN25 I2C BUS connector Part Number Appendix B System AssignmentsDMA channel assignments System I/O Ports1st MB Memory Map Interrupt assignments Table B.4 Interrupt assignmentsPage Appendix C Mechanical DrawingsBoard Mechanical Drawings Figure C.1 PCM-3362 Mechanical Drawing Component SideAppendix C Mechanical Drawings Heatsink Mechanical Drawings Figure C.3 PCM-3362N Heatsink Mechanical DrawingOptional Heat spreader Mechanical Drawings Figure C.5 PCM-3362 optional Heatspreader Mechanical DrawingPage Watchdog Timer and Gpio sample code Appendix DWatchdog Timer sample code Bit 10=Reserved Bit 62Reserve=00000Appendix D Watchdog Timer and Gpio sample code Gpio sample codePage Appendix D Watchdog Timer and Gpio sample code