Acer M5150 manual

Page 6

Introducing the Motherboard	1
Features	2
Mainboard Components	4
Block Diagram	5
ixtreme M5150	6
I/O Port Introduction	9
Hardware Specifications and Configurations	12
Using BIOS	16
Setup Utility Menus	17
Product Information	19
Standard CMOS Features	20
Advanced BIOS Features	21
Advanced Chipset Features	24
Integrated Peripherals	25
Power Management Setup	26
PC Health Status	28
Frequency/Voltage Control	29
BIOS Security Features	30
Load Default Settings	31
Machine Disassembly and Replacement	32
General Information	33
Standard Assembly Process	34
Standard Disassembly Process	50
Troubleshooting	65
Power-On Self-Test (POST)	66
POST Error Messages List	70
Error Symptoms List	72
Undetermined Problems	76
Jumper and Connector Information	77
FRU (Field Replaceable Unit) List	91
Exploded Diagram	91
FRU List	97

VI

Image 6

Contents Ixtreme M5150 Service Guide Date Chapter Updated Revision HistoryCopyright Conventions Preface Page Introducing the Motherboard IntroductionFeatures Bios Firmware Dimensions and weightMainboard Components Label ComponentBlock Diagram Ixtreme M5150 Icon Component DescriptionRear view Audio Jack Function Table Color/Use Headphone1CH Port Introduction Component DescriptionKeyboard PS/2 or USB, manufacturing option System PeripheralsMouse PS/2 or USB, manufacturing option SpeakersCard Reader Option Specification Hardware Specifications and ConfigurationsBios Hotkey List Main Board Major ChipsVideo Interface System MemoryCache Memory Audio InterfaceUSB Port Power ManagementIDE Interface Suspend to Devices Idle Shut DownGlobal Standby Mode Power Management Function Acpi support functionDevice Standby Mode Suspend ModeStandard Configuration Using BiosAbout the Setup Utility Entering the Setup UtilitySetup Utility Menus Updating the Bios Cmos Setup Utility Product Information Item Help Product InformationStandard Cmos Features Date and TimeHalt On All, But Keyboard Advanced Bios Features Quick Boot EnabledQuiet Boot Enabled UHard Disk Drive Priority Press Enter Removable Device Priority Press Enter AMD-V Enabled Advanced Chipset FeaturesAMD Cool ‘n’ Quiet Enabled Primary Video AutoIntegrated Peripherals Power On by RTC Alarm Disabled Power Management SetupDeep Power Off Mode Enabled Power On by PCIE/PCI Devices DisabledWake Up by PS/2 KB/Mouse Enabled Wake Up by USB KB/Mouse EnabledRestore On AC Power Loss Last State Smart Fan Enabled PC Health StatusSpread Spectrum Enabled Frequency/Voltage ControlUser Password Not Installed Bios Security FeaturesSupervisor Password Not Installed Change Supervisor Password Press EnterLoad Default Settings Save & Exit SetupMachine Disassembly and Replacement General Information Before You BeginStandard Assembly Process Opening the chassisRemoving front bezel and HDD Cage Page Install the PSU Setting the MotherboardPage DIMM4 DIMM3 DIMM2 DIMM1 Assembly motherboard Page ODD Installed on SATA4 Insert the ODD/HDDPage HDD Carrier Installed on SATA3 Master HDD Installed on SATA1 Slave HDD Installed on SATA2 Close the Front BezelInsert Add-on card Page Page Install system fan Overview Standard Disassembly Process Opening the computerRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Removing the ODD Removing the System Fan Removing the Main Board Page Page Removing the power-supply Removing the HDD in HDD CarrierPage Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Post Error Messages List Bios Messages Action/FRUSpecifics about the type and location of the memory error Main board and Memory Error Symptoms ListError Symptom Action/FRU Processor / Processor Fan Hard Disk DriveError Symptom Action/FRU CD/DVD-ROM Drive AudioParallel/Serial Ports Error Symptom Action/FRU Video and MonitorPower Supply KeyboardError Symptom Action/FRU Other ProblemsUndetermined Problems Installing the Motherboard in a Case Jumper and Connector InformationSafety Precautions Choosing a Computer CaseChecking Jumper Settings Setting JumpersChecking Jumper Settings Jumper SettingsJumper Type Description Setting Default IIIustration Connecting Case Components Connecting 24-pin power cablePin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionPwrfan Cooling Fan Power Connector Pin Signal Name Function ATX12V ATX 12V Power Connector Pin Signal NameReset Switch Pin Signal Name FunctionPower/Sleep/Message waiting LED Power SwitchInstalling Hardware Installing the ProcessorBefore installing the Processor CPU Installation Procedure Installing Memory Modules Installation ProcedureMemory Memory Bus Installing Serial ATA Hard Drives Sata cable optional Sata power cable optionalInstalling Add-on Cards PCIE16X SlotOnboard PCI interface does not support 64-bit Scsi cards Connecting Optional Devices FAUDIO1 Front Panel Audio headerSata 1~6 Serial ATA connectors SPDIFOUT1 Spdif out headerOptionFRU Field Replaceable Unit List Exploded Diagram ChassisPB 30L w/ HDD carrier ME BOMRAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM Oddbuttontop Oddbuttonbottom Page FRU List