Metrologic Instruments MS2422, MS2421 manual Full Speed USB

Page 22

INSTALLATION

CABLE INSTALLATION (INTERFACE SPECIFIC)

FULL SPEED USB

The following steps describe how to properly install the cables for a Full Speed USB scanner application. The scanner must then be configured to match the host’s USB parameters. Cable installation alone does not guarantee that the scanner will communicate properly with the host system.

Configuration bar codes are located in the MetroSelect Configuration Guide (MLPN 00-02407x) and the MS2xxx Stratos Series Configuration Addendum (MLPN 00-02034x).

1.Turn off the host system.

2.Plug the 10-pin RJ45 end of the USB interface cable (MLPN 57-57201x-N-3 or 57-57227x-N-3) into the 10-pin socket labeled, Scanner Host USB, on the bottom of the scanner. Refer to Figure on page 19.

3.Connect the other end of the USB interface cable to the appropriate USB port on the host device.

Before continuing verify that the USB interface cable is connected to the appropriate socket on the scanner. An incorrect cable connection can cause communication problems or potential damage to the scanner and/or terminal.

Manufacturers Note: Plugging the scanner into the USB port of the host does not guarantee that scanned information will appear at the host. A software driver and correct configuration setting are also required for proper communication to occur.

4.Plug the external power supply (MLPN 46-002xx) into the 3-pin Molex socket labeled, DC Power In, on the bottom of the scanner.

Check the AC input requirements of the power supply to make sure the voltage matches the AC outlet. The outlet should be located near the equipment and be easily accessible.

Metrologic recommends using a switched AC outlet. The switch should be located on the operator’s side of the checkout counter in close proximity to the scanner to facilitate calibration and service of the unit.

5.Connect AC power to the transformer. If the AC outlet is equipped with an on/off switch, turn the power on.

6.Turn on the host system.

7.Configure the scanner to match the host system’s USB parameters.

The IBM OEM Full Speed USB Communication Defaults** bar code is located in the

MS2xxx Stratos Series Configuration Addendum (MLPN 00-02034x) under Scanner Configuration Bar Codes:

Dual Cable Scanner Configuration Bar Codes, IBM OEM Full Speed USB Communication Defaults and IBM OEM Full Speed USB Protocols.

**Applies only with MS2421 non-scale scanner models. If a scale has been integrated into a scale ready MS2421, the configuration bar code shown does not apply.

18

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Metrologic INSTRUMENTS, INC Copyright TrademarksTable of Contents EMC Manual Scope IntroductionProduct Overview Base KIT Components Optional AccessoriesDescription Replacement Parts General Precautions See caution statement onMS2421 / MS2422 Scanner Design Specifications Design Specifications OperationalBase Model Characteristics MS2421 ScannerDimensions MS2421 Label Locations Top and Examples Bottom MS2422 Scanner MS2422 Dimensions MS2422 Label Locations Top and Examples Bottom Quick Installation Outline InstallationSite Requirements Unpacking the Unit Installing the Unit in the Counter MS2422 Mounting Diagram Cable Installation Interface Specific RS232RS232 Interface Cable Installation Schematic Full Speed USB USB Cable Installation Schematic IBM IBM Cable Installation Schematic Cable Installation Secondary Metrologic Scanner Secondary Scanner Cable Installation Schematic Base Model Checkpoint Recommended Switch Bank Settings EAS DeactivationScanner Operation Scan ZoneHorizontal Direct 13 mil Wake Activation Area Photocell LED Output Wake Activation Area Sensitivity Photocell LED Output Range One Beep Three Beeps on power upAudible Razzberry ToneBlue LED Off Visual Steady BlueSteady Blue and Single blue Flash Flashing BlueDiagnostic Indicator Display Error Code Display Optional Product Roll Bar ShownScanner Operation Scanner Operation Laser & Motor Off Power Save Mode Blink Power Save ModeLaser Off Power Save Mode Dual Action Power Save Mode #1Waking the Unit from All Power Save Modes Changing the Beeper VolumePlacing the Unit in Laser & Motor Off Power Save Mode Beeper Options and Button FunctionsConfiguration Mode POWER-UP Test ModeStartup Maintenance Horizontal Scan Window ReplacementDaily Maintenance Troubleshooting Same symbol timeout isScanner and the communication port match and the program is RS232 Demonstration Program On Error GotoPrint Error NO. ERR Press ANY KEY to Terminate Close SystemDefault Settings Communication ParametersIBM 46 USB IBM USB ACK / NAK Multiple Selections Default Settings Default settings for Aux interface Scanner and Cable Terminations EASSIG2 Scale Ready MS2421 Models Additional Pinout ConnectionsSIG1 SIG3Cable Connector Configurations PC+5V USBPinFunction† ITE Equipment SafetyRegulatory Compliance LaserFunkstöreigenschaften nach EN550221998 RemarqueEuropean Standard Standard EuropeoClass B Devices AvertissementLimited Warranty Metrologic Instruments, IncPatents Index 39, 46, 4739-41 Page Page January 2009, Version
Top Page Image Contents