Metrologic Instruments MS951 manual ScanPal Data Collector, Test Modes

Page 49

Enter/Exit Program Mode

* *

ScanPal Data Collector

The Metrologic ScanPal is a data collection terminal used with the MS951 scanner. The following bar codes are used to configure the scanner to communicate with the ScanPal.

Default to ScanPal

When this option is selected, the scan-

Communication Parameters

ner’s parameters will automatically

change to the default settings of the

ScanPal data collector.

I

B

5

Transmit Code ID

L P 6

**Do Not Transmit Code ID

L P 5

When this mode is selected, the scanner will transmit a code type identifier before each bar code. This feature is used with the ScanPal for special applications.

Test Modes

Scan Count

S M 3

When this option is scanned, the scanner will enter scan count test mode. The firm- ware number of the scanner will also be transmitted to the host device. Do not enable this feature unless instructed to do so by a Metrologic representative.

Scannability

S M 2

*Normal Scan

S M 1

Transmit Scanner Parameters

I B 6

When this option is enabled, the scanner will enter scannability test mode. Do not enable this feature unless instructed to do so by a Metrologic representative.

When this option is selected, the scanner will exit from scannability or scan count test modes.

When this option is selected, the scanner will transmit (via Keyboard Wedge and at 9600 baud via RS-232) its current configuration.

44

Image 49

Contents Metrologic INSTRUMENTS, INC Locations Table of Contents Page Page Scope of the MS951 Programming Guide Programming the Scanner Recall Defaults Enter Program ModeLaser Operation Laser Activation RangeIdentical Symbol Re-Scan Indicator Same Symbol Re-ScanVs 2 Scan Buffers Decode Options Beeper Tones Audible Indicators for Communication Timeouts RS-232 Parameter Baud Rate RS-232 InterfaceRS-232 Parameter Data Bits RS-232 Parameter ParityRS-232 Parameter Software Handshaking RS-232 Parameter Hardware HandshakingIntercharacter Delay DE Disable Command RS-232 Parameter Scanning Control DTR SignalRecord Header/Terminator Select Longitudinal Redundancy Check LRCSTX Prefix Off UPC/EAN Identifiers KB Parameter Keyboard Type Keyboard Wedge KB InterfaceKB Parameter Keyboard Country Type Recall Defaults Reserved KB Parameter Alt Mode KB Parameter Caps Lock ModeKB Parameter XT Clean-Up Bit KB Parameter Inter Scan Code Delay AT and PS/2 ModesWhen this option is on, the scanner will transmit a TAB Ascii 09H after each bar code KB Parameter Special Features Ocia Options IBM 46XX Options IBM 46XX Parameter Inter Record DelayLight Pen Options Code Type Selections Light Pen Emulation FeaturePage Enable Code Disable Code Minimum Code Length for All Code Types Code Length Minimum FeatureUPC-A Options UPC/EAN CodeUPC-E Options UCC Supplemental Options Disable 5 Digit SuppsCoupon Code Supplemental Isbn OptionsNer will scan Code 39 bar codes CodeCodabar Enable Clsi Editing Do Not Transmit Start/StopInterleaved 2 of 5 ITF Interleaved 2 of 5 ITF Symbol Lengths Digits Recall Defaults Digits MSI Plessey Check Digit ITF Minimum Symbol Length TestSome UK libraries UK Plessey OptionsTest Modes ScanPal Data CollectorSpecial Features Way to disable this feature is by Locks on 16, 20, 23, 28 and 30 character bar codes User Programmable Prefix and Suffix ID Characters RB0 RB9 Bar Codes Ascii Reference Table HEX Value Decimal Character Less than Letter O 104 PC Extended Reference Key Tables Function keys F1 F12 and other keys No E0H required PC Extended Key Reference TablesCode Assigned Function Reserved CodesRAA Page Page Page Page Page Page Page Page Page Page Disclaimer DisclaimerACK/NAK IndexNewcode UPC-A