Canon FB636U, FB630U manual Error Messages, Cause, Response

Page 62

A P P E N D I C E S

Error Messages

Error Message

Scanner is Not Detected

Cannot Communicate with Scanner

Minimum Memory Requirements Not Met. Retry after Increasing Free Memory.

Home Position Not

Detected

File Access Error (FB63U

Button Manager) Error

Code = 36

An error has occurred. (Sense Code=xx, Additional Sense Code=xx, Additional Code Condition=xx)

Cause

USB cable not connected correctly.

Scanning unit is locked (lock switch is not released)

USB cable not connected correctly.

Memory is insufficient for the required volume of the scanned image data.

Lock not released.

The lamp is burnt out.

Plug-in Module CS-U is already installed.

Another error has occurred.

Response

Use the USB cable to connect the Macintosh to the scanner properly.

Release the lock switch at the base of the scanner

Ensure the USB cable is securely fastened to the Macintosh and scanner.

Reduce the scan area to the minimum possible scope and lower the resolution and magnification settings for the output device.

Close all application programs that are running other than PhotoDeluxe 2.0.

Increase the memory allocated to PhotoDeluxe 2.0.

After releasing the lock, temporarily disconnect the USB cable. Reconnect it and restart Plug-in Module CS-U 3.3.

Contact your nearest Canon Customer Support Help Desk.

Reinstall after emptying the Trash.

Note down the Sense Code, Additional Sense Code and error message and contact the nearest Canon Customer Support Help Desk.

62

Image 62
Contents Users Guide How to Make Best Use of the Manuals Getting StartedAbout the Conventions Used in this Guide How to Use this GuideWhere to Look Table of Contents Adjusting and Editing Scanned Images AppendicesControl Panel Features E P Scanning ProceduresAdjusting and Editing Scanned Images Scanning Preparations pGamma Curve Adjusts Image Brightness Plug-in Module CS-U Special FeaturesSee the Results of Adjustments Immediately Dynamic Preview Supports ColorSync 2.0 or higher Auto Tone CorrectionStart Plug-in Module CS-U Installing Plug-in Module CS-UQuick Start Instructions Start the Preview ScanClick on the Browser button Set the preferences, magnification and scan mode settingsSpecify the Area of the Image to be Scanned p Select the area to be scanned by clicking and draggingSave the image with the application software, specifying a Scan the Image pClick on the Scan button Folder, file name and file formatE P Operating Environment Installing Plug-in Module CS-UE P E P Procedures Click the Install the Software buttonClick the Yes button to start the installation E P E P Scanning Preparations Display Plug-in Module CS-U Control Panel ButtonsAdobe Photoshop E P Operating ProceduresAdobe PhotoDeluxe Click on the Preview button PreviewingSet the original on the scanner document glass Set Preferences UnitE P Setting Basic Resolution Preview Window Settings Dialog Box E P Preview Window SizeSelect the Prefs menu in the control panel Return to Default SettingsE P Calibration Select the desired option from the pull-down menuOutput Device Resolution= 360 dpi, Magnification= 100% Set MagnificationE P To Set the Magnification Factor Set the desired magnification factor on the control panelBlack and White Mode Diffusion Dither Set Scan ModeBlack and White Mode Line Grayscale Mode 8-bitColor Mode 24-bit High Definition ColorTo Set the Scan Mode Select the scan mode that you wantVerify Image Before Scanning To Verify the ImageE P Scanning Scan Area Settings Position the pointer in the preview windowSelect the area you want to enlarge with the zoom function ZoomingTo Zoom Click on the Zoom In button To return to normal view, click the Zoom Out buttonSpecify the Scan Area ScanningTo Initiate the Scan Saving Scanned Images To Save an ImageBlack & White Mode Color ModeGrayscale Mode Diffusion DitherHow to Adjust Histograms Using the Histogram Feature to Adjust Image ContrastHow to Interpret Histograms Click the Auto button E P To Adjust a HistogramClick on the Histogram button Click on the OK buttonAdjusting the Image with Gamma Settings Setting the GammaGamma = GammaBrightness Brightness and Contrast SettingsContrast Click the OK button E P To Adjust the Brightness and ContrastClick the gamma button CRT Type B Adjusting Gamma with the MenuCRT Type a CRT Type CE P To Change the Gamma Value Settings Click the radio button for Menu SettingSending Output to a Printer Gamma Value SettingsAdjusting the Gamma Value to Match the Display Slider Tone Curve Settings Manipulating the GraphE P To Edit the Tone Curve Auto Tone Correction ColorSync To Activate the ColorSync FunctionOpen the Image menu and select Descreen ProcedureDescreen To Set the Threshold Value Set the threshold value in the Control PanelSaving / Recalling Settings To Save Settings in a Settings FileE P To Recall a Settings File Editing Scanned Images Many special effects may be achieved with filtersScanning Techniques Matching Scan Resolution to PurposeOptical and Enhanced Resolutions System Requirements SpecificationsFunctional Specifications Clicked on the Plug-in Module CS-U control panel TroubleshootingProblem Scan button cannot be selected Cause Error MessagesError Message ResponseGlossary Preview ResolutionImage File ScannerIndex P E N D I C E S Canon Customer Support Help Desk HelpdeskOE-030AA 0799 CDS Canon Inc