Canon FB630U Quick Start Instructions, Installing Plug-in Module CS-U, Start Plug-in Module CS-U

Page 9

Quick Start Instructions

Those who wish to start scanning immediately should follow the procedures below. If you require further information at any stage, read the pages referenced at each step.

Installing Plug-in Module CS-U

 

p. 13

1

1. Place the Macintosh version of the CanoScan Setup CD-ROM

that came with the scanner into the computer’s CD-ROM drive.

The CanoScan Setup Utility will automatically start. (If the

CanoScan Setup Utility does not automatically start, double- click the [CanoScan FB630U/636U] icon, followed by the [Setup] icon.)

2. Click [Install the Software] and install Plug-in Module CS-U. (Install Adobe PhotoDeluxe 2.0 first.)

If Adobe PhotoDeluxe 2.0 has not yet been installed, install it before Plug-in Module CS-U.

Start Plug-in Module CS-U

 

p. 19

2

1. Connect the scanner to the computer, then start Adobe

PhotoDeluxe 2.0.

 

 

2.Select [CanonPI CS-U 3.3.0...] as the image source (this step is only required the first time the scanner is used with the program)

3.Click the scanner icon.

Plug-in Module CS-U will start and display its control panel.

Start the Preview Scan

 

p. 21

3

1.

Place the materials to be scanned on the scanner.

2.

Click the preview scan button ( ).

 

 

• The entire document glass area will be scanned and displayed in the

preview scan window.

Preview Window

Plug-in Module CS-U automatically calibrates itself the first time the preview or scan button is clicked. The scanner will run by itself for a few moments without displaying an image in the window. This does not constitute a breakdown. The calibration results are stored until the computer power is shut off.

9

Image 9
Contents Users Guide Getting Started How to Make Best Use of the ManualsHow to Use this Guide Where to LookAbout the Conventions Used in this Guide Table of Contents Appendices Adjusting and Editing Scanned ImagesControl Panel Features Adjusting and Editing Scanned Images Scanning ProceduresE P Scanning Preparations pSee the Results of Adjustments Immediately Dynamic Preview Plug-in Module CS-U Special FeaturesGamma Curve Adjusts Image Brightness Supports ColorSync 2.0 or higher Auto Tone CorrectionQuick Start Instructions Installing Plug-in Module CS-UStart Plug-in Module CS-U Start the Preview ScanSpecify the Area of the Image to be Scanned p Set the preferences, magnification and scan mode settingsClick on the Browser button Select the area to be scanned by clicking and draggingClick on the Scan button Scan the Image pSave the image with the application software, specifying a Folder, file name and file formatE P Installing Plug-in Module CS-U E POperating Environment Click the Install the Software button E P ProceduresClick the Yes button to start the installation E P E P Scanning Preparations Buttons Display Plug-in Module CS-U Control PanelE P Operating Procedures Adobe PhotoDeluxeAdobe Photoshop Previewing Set the original on the scanner document glassClick on the Preview button Unit Set PreferencesE P Setting Basic Resolution E P Preview Window Size Preview Window Settings Dialog BoxE P Calibration Return to Default SettingsSelect the Prefs menu in the control panel Select the desired option from the pull-down menuSet Magnification Output Device Resolution= 360 dpi, Magnification= 100%Set the desired magnification factor on the control panel E P To Set the Magnification FactorBlack and White Mode Line Set Scan ModeBlack and White Mode Diffusion Dither Grayscale Mode 8-bitHigh Definition Color Color Mode 24-bitSelect the scan mode that you want To Set the Scan ModeTo Verify the Image Verify Image Before ScanningE P Scanning Position the pointer in the preview window Scan Area SettingsZooming To ZoomSelect the area you want to enlarge with the zoom function To return to normal view, click the Zoom Out button Click on the Zoom In buttonScanning To Initiate the ScanSpecify the Scan Area To Save an Image Saving Scanned ImagesGrayscale Mode Color ModeBlack & White Mode Diffusion DitherUsing the Histogram Feature to Adjust Image Contrast How to Interpret HistogramsHow to Adjust Histograms Click on the Histogram button E P To Adjust a HistogramClick the Auto button Click on the OK buttonSetting the Gamma Adjusting the Image with Gamma SettingsGamma Gamma =Brightness and Contrast Settings ContrastBrightness E P To Adjust the Brightness and Contrast Click the gamma buttonClick the OK button CRT Type a Adjusting Gamma with the MenuCRT Type B CRT Type CClick the radio button for Menu Setting E P To Change the Gamma Value SettingsGamma Value Settings Adjusting the Gamma Value to Match the DisplaySending Output to a Printer Slider Manipulating the Graph Tone Curve SettingsE P To Edit the Tone Curve To Activate the ColorSync Function Auto Tone Correction ColorSyncProcedure DescreenOpen the Image menu and select Descreen Set the threshold value in the Control Panel To Set the Threshold ValueTo Save Settings in a Settings File Saving / Recalling SettingsE P To Recall a Settings File Many special effects may be achieved with filters Editing Scanned ImagesMatching Scan Resolution to Purpose Optical and Enhanced ResolutionsScanning Techniques Specifications Functional SpecificationsSystem Requirements Troubleshooting ProblemClicked on the Plug-in Module CS-U control panel Scan button cannot be selected Error Message Error MessagesCause ResponseGlossary Image File ResolutionPreview ScannerIndex P E N D I C E S Helpdesk Canon Customer Support Help DeskOE-030AA 0799 CDS Canon Inc