Datalogic Scanning 6000 PLUS manual Disable ACK/NAK

Page 25

RS-232 ACK/NAK Options (QuickScan 6000 Plus ONLY)

Several ACK/NAK parameters can be set for your QuickScan 6000 Plus scanner. Contact your Datalogic dealer if the specific ACK/NAK option you wish to set is not included in this section.

Options for RS-232 ACK/NAK are:

•Disable ACK/NAK

•Enable ACK/NAK for bar code transmission

•Enable ACK/NAK for host command acknowledge

•Enable ACK/NAK for bar code transmission and host command acknowledge.

(These features available for QuickScan 6000 Plus ONLY)

SET ----------------------------------------------

ACK/NAK ENABLE

DISABLE ACK/NAK -------------------

FOR BAR CODE TRANSMISSION --------

FOR HOST COMMAND ACKNOWLEDGE --

FOR BAR CODE TRANSMISSION --------

AND HOST COMMAND ACKNOWLEDGE

END ----------------------------------------------

Programming Guide

21

Image 25

Contents QuickScan 6000/6000 Plus Datalogic Scanning, Inc Contents Additional Information SymbologiesSample Bar Codes Integrating Peripherals With Host Systems Understanding the BasicsHardware Changing InterfacesSoftware Wand Emulation Keyboard Wedge RS-232Customizing Your Scanner Operation How To Program Using Bar Codes What Is Programming Mode?Programming Overview Programming Session Scanner Response When In Programming ModeIf You Make a Mistake Return to Factory SettingsWhere To Go From Here IBM 4683/84 4693/94 Port 5B Interface Selection IBM 4683/84 4693/94 Port 5B SettingsSend AS Code Dont Send AS Code ENDIBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E SettingsIBM 4682/92 Port E Interface Selection IBM 4682/92 Port E SettingsNCR Ocia Nine Bit long format Interface Selection Datalogic OCIA1 Interface SelectionSNI Ocia Interface Selection Ocia Options Enable Disable ENDWand Emulation Interface Selection Wand Emulation SettingsTransmit in C39 Transmit PRE-NOISE LOW HighSNI RS-232 Interface Selection RS-232 Interface SelectionRS-232 Communication Parameters Data Format Table Baud RateNone Even ODD Mark Space ONE TWO Seven Bits Eight Bits END Data Format SettingsHandshaking Hardware ControlSET Enable XON/ Xoff Disable XON/XOFF ENDThese features available for QuickScan 6000 Plus only Disable ACK/NAKIntercharacter Delay = 90 Milliseconds = 100 Milliseconds END Keyboard Wedge Communication Parameters PC Keyboard Wedge Interface SelectionT YPE PC Keyboard Wedge Connect to a Laptop/No Keyboard Attached Keyboard Attached Enable Disable ENDSET Caps Lock OFF Caps Lock on Caps Lock QuickScan 6000 Plus onlyCountry Mode QuickScan 6000 Plus only Spain Sweden Switzerland Japanese 106-KEY END Country Mode QuickScan 6000 Plus onlyIntercharacter Delay Intercharacter Delay Prefix & Suffix RS-232 and Keyboard Wedge Interfaces OnlyProgramming Guide Setting Non-Symbology Specific Prefixes Non-Symbology Specific ItemsSET SET Prefix Entering Programming Mode Setting Non-Symbology Specific SuffixesSET SET Suffix Setting Prefix and/or Suffix Characters Setting a Single Character Prefix or SuffixONE Character only Ascii Character Set Setting Symbology-Specific Label Identifiers Label I.D Symbology-Specific Label I.DIndustry Standard Label Identifiers all are prefixes Setting Symbology Specific Label Identifiers Label I.D Label I.D. Symbology Selection EAN-13 W/5 Digit ADD- on EAN-13 W/2 Digit ADD- onEAN-13 W/C128 ADD- on ODEThis example 8 equals 38hex How to Set Single Character Label I.DSymbology Specific Label Identifiers Characters Disabling Label I.D. for a Specific SymbologyEND Symbologies Symbology Options Overview Enable All Symbologies Disable All Symbologies1 Universal Symbology SelectionStandard 2 of 5 must be enabled before Iata can be enabled SET Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Symbology SelectionEnable IATA3 Disable Iata Enable MSI/PLESSEY Disable MSI/PLESSEY Enable Codabar Disable Codabar Enable Code Disable CodeUPC/EAN Options Dont Expand EXPAND1 UPC/EAN ExpansionDont Expand END UPC/EAN Add-Ons Optional Required Disabled ENDC128 and Custom Add-Ons Enable 4 Digit Check Enable 5 Digit Check Price/Weight Check DigitUPC Data Format Settings Send NSD1 Dont Send NSD1 Send Check DIGIT2 Send Check DigitSend NSD2 Dont Send NSD2 END EAN Data Format Settings Code 39 Options Code Dont Compute Dont Transmit Enable Disable ENDSetting Lengths END Code 128 Options AIM Symbology ID PrefixInterleaved 2 of 5 Label Lengths Interleaved 2Check Digit and Variable Length Label Selections Setting Fixed Lengths Setting Interleaved 2 of 5 Fixed and Minimum Label LengthsSetting Minimum Label Length Set FixedSET First Fixed Length Standard 2 of 5 Label Lengths Standard 2Check Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Standard 2 of 5 Fixed and Minimum Label Lengths 5 Fixed Abel Lengths Tandard Minimum Codabar Options Codabar Check Digit & Variable Length Format = abcd/abcd END Codabar Start/Stop CharacterCodabar Fixed Length Enable FixedCodabar SET Fixed Lengths ONE Check Digit TWO Check Digits END MSI/Plessey Check DigitMSI/Plessey Fixed Length MSI/PLESSEY SET Fixed Lengths Good Read Beeper Settings General FeaturesOFF Universal Read Verification Read VerificationVerify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13 Read Verification by SymbologyVerify Code Verify Interleaved 2 Disable LOW Power Idle Low Power ModeAutoSense Stand Mode Debug ModeCreating MultiFunction Labels Host ProgrammingNeed More Information? Appendix B Sample Bar Codes UPC-E QuickScan 6000/6000 Plus Default Wand Keyboard Symbology RS-232 I/F Code 128 Options Transmit Don’t Transmit Codabar Options ABCD/ABCD Page Australia

Related manuals

Manual 104 pages 8.11 Kb