Datalogic Scanning 6000 PLUS manual Verify Interleaved 2

Page 88

READ VERIFICATION SYMBOLOGY TYPE

VERIFY READS (APPLIES TO ALL SYMBOLOGIES

VERIFY INTERLEAVED 2 OF 5 ------

VERIFY STANDARD2 2 OF 5 --------

VERIFY CODABAR -------------------

VERIFY CODE 93 ------------------

VERIFY CODE 128 ----------------

VERIFY MSI/PLESSEY -------------

ONE READ -------------------------

TWO READS ------------------------

THREE READS ----------------------

FOUR READS -----------------------

END ----------------------------------------------

2The Standard 2 of 5 symbology is available for QuickScan 6000 Plus scanners ONLY.

84	QuickScan 6000/6000 Plus

Image 88

Contents QuickScan 6000/6000 Plus Datalogic Scanning, Inc Contents Additional Information SymbologiesSample Bar Codes Understanding the Basics Integrating Peripherals With Host SystemsHardware Changing InterfacesSoftware RS-232 Wand Emulation Keyboard WedgeCustomizing Your Scanner Operation How To Program Using Bar Codes What Is Programming Mode?Programming Overview Scanner Response When In Programming Mode Programming SessionReturn to Factory Settings If You Make a MistakeWhere To Go From Here IBM 4683/84 4693/94 Port 5B Settings IBM 4683/84 4693/94 Port 5B Interface SelectionSend AS Code Dont Send AS Code ENDIBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E Settings IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F SelectionIBM 4682/92 Port E Settings IBM 4682/92 Port E Interface SelectionNCR Ocia Nine Bit long format Interface Selection Datalogic OCIA1 Interface SelectionSNI Ocia Interface Selection Enable Disable END Ocia OptionsWand Emulation Interface Selection Wand Emulation SettingsTransmit in C39 LOW High Transmit PRE-NOISESNI RS-232 Interface Selection RS-232 Interface SelectionRS-232 Communication Parameters Baud Rate Data Format TableData Format Settings None Even ODD Mark Space ONE TWO Seven Bits Eight Bits ENDHardware Control HandshakingEnable XON/ Xoff Disable XON/XOFF END SETDisable ACK/NAK These features available for QuickScan 6000 Plus onlyIntercharacter Delay = 90 Milliseconds = 100 Milliseconds END PC Keyboard Wedge Interface Selection Keyboard Wedge Communication ParametersT YPE Keyboard Attached Enable Disable END PC Keyboard Wedge Connect to a Laptop/No Keyboard AttachedCaps Lock QuickScan 6000 Plus only SET Caps Lock OFF Caps Lock onCountry Mode QuickScan 6000 Plus only Country Mode QuickScan 6000 Plus only Spain Sweden Switzerland Japanese 106-KEY ENDIntercharacter Delay Intercharacter Delay RS-232 and Keyboard Wedge Interfaces Only Prefix & SuffixProgramming Guide Setting Non-Symbology Specific Prefixes Non-Symbology Specific ItemsSET SET Prefix Entering Programming Mode Setting Non-Symbology Specific SuffixesSET SET Suffix Setting a Single Character Prefix or Suffix Setting Prefix and/or Suffix CharactersONE Character only Ascii Character Set Setting Symbology-Specific Label Identifiers Label I.D Symbology-Specific Label I.DIndustry Standard Label Identifiers all are prefixes Setting Symbology Specific Label Identifiers Label I.D Label I.D. Symbology Selection EAN-13 W/2 Digit ADD- on EAN-13 W/5 Digit ADD- onEAN-13 W/C128 ADD- on ODEHow to Set Single Character Label I.D This example 8 equals 38hexDisabling Label I.D. for a Specific Symbology Symbology Specific Label Identifiers CharactersEND Symbologies Symbology Options Overview Enable All Symbologies Disable All Symbologies1 Universal Symbology SelectionStandard 2 of 5 must be enabled before Iata can be enabled Symbology Selection SET Enable UPC/EAN Disable UPC/EAN Enable Code Disable CodeEnable IATA3 Disable Iata Enable Codabar Disable Codabar Enable Code Disable Code Enable MSI/PLESSEY Disable MSI/PLESSEYUPC/EAN Options Dont Expand EXPAND1 UPC/EAN ExpansionDont Expand END UPC/EAN Add-Ons Optional Required Disabled ENDC128 and Custom Add-Ons Enable 4 Digit Check Enable 5 Digit Check Price/Weight Check DigitUPC Data Format Settings Send NSD1 Dont Send NSD1 Send Check DIGIT2 Send Check DigitSend NSD2 Dont Send NSD2 END EAN Data Format Settings Code 39 Options Dont Compute Dont Transmit Enable Disable END CodeSetting Lengths END AIM Symbology ID Prefix Code 128 OptionsInterleaved 2 Interleaved 2 of 5 Label LengthsCheck Digit and Variable Length Label Selections Setting Interleaved 2 of 5 Fixed and Minimum Label Lengths Setting Fixed LengthsSetting Minimum Label Length Set FixedSET First Fixed Length Standard 2 Standard 2 of 5 Label LengthsCheck Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Standard 2 of 5 Fixed and Minimum Label Lengths 5 Fixed Abel Lengths Tandard Minimum Codabar Options Codabar Check Digit & Variable Length Codabar Start/Stop Character Format = abcd/abcd ENDEnable Fixed Codabar Fixed LengthCodabar SET Fixed Lengths MSI/Plessey Check Digit ONE Check Digit TWO Check Digits ENDMSI/Plessey Fixed Length MSI/PLESSEY SET Fixed Lengths General Features Good Read Beeper SettingsOFF Read Verification Universal Read VerificationVerify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13 Read Verification by SymbologyVerify Code Verify Interleaved 2 Low Power Mode Disable LOW Power IdleDebug Mode AutoSense Stand ModeCreating MultiFunction Labels Host ProgrammingNeed More Information? Appendix B Sample Bar Codes UPC-E QuickScan 6000/6000 Plus Default Wand Keyboard Symbology RS-232 I/F Code 128 Options Transmit Don’t Transmit Codabar Options ABCD/ABCD Page Australia

Related manuals

Manual 104 pages 8.11 Kb