Pioneer PRO-610HD Coarse Adjustment and Fine Adjust- ment of the Blue, Confirmation of Adjustment

Page 20

PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5

3.6.5

Repeat procedures 3.6.2 through 3.6.4 for the other screen modes. (Completion of the red adjustment)

3.7 Coarse Adjustment and Fine Adjust- ment of the Blue

Make coarse and fine-adjustments of the blue in the same manner as with the red, described in 3.5 and 3.6.

3.8 Confirmation of Adjustment

After the green, red, and blue adjustments are finished, check convergence errors with the patterns for all three colors on the monitor.

Check the patterns in all SCREEN modes, and if any error in convergence is recognized, readjust convergence in MANUAL CONVER. mode.

Note: Be sure NOT to change the green pattern during readjustment.

IMPORTANT!

(1)When all the adjustments are completed, or when adjustment should be temporarily interrupted, adjustment data must be written to the EEPROM, in the following manner:

When all the adjustments are completed, or to interrupt adjustment, press the MENU key to quit Convergence Adjustment mode. The display will be unstable for several seconds, but this is because the data are being written to the EEPROM. Wait without doing anything until the display becomes stable, which means writing of data to the EEPROM is finished.

If the power of the TV is turned off (standby) during Convergence Adjustment mode (coarse and fine-adjustments), turn on the TV, enter FACTORY mode, and enter Convergence Adjustment mode by pressing the SET/ENTER key. Then press the MENU key. The data will be written to the EEPROM as described above.

(2)Do NOT turn off the main power during or after convergence adjustment.

If you do so, the adjusted data may be lost. If the data are lost, you must make all the adjustments again.

(3)When the CENTER POINT (test cross) or MULTI-POINT (user convergence) adjustments have been made by a user, and if the unit enters FACTORY Convergence Adjustment mode (with the DOT and SET/ENTER keys), the user's adjustment data will be all cleared and returned to the factory-preset values.

Be sure NOT to enter this Convergence Adjustment mode except when a repair related to convergence or a repair that requires convergence adjustment later, is needed.

If you inadvertently enter Convergence Adjustment mode, readjust the convergence.

7White Balance Adjustment

7-1Contrast Adjustment

Start

1st FAC

"Color Bar"

1 2 3 4

1 2 3

4 5 6

7 8 9

0

CHVOL

3

5

2 3

8 °￿

ë￿

ADJUSTMENT OFFSET

"Normal video signal"

CONTR

Adjust the screen to optimum condition.

At the TP-BK of the B CRT DRIVE Assy, check that the signal is shaped as shown below.

Saturated

Shapely waveform

Shapeless waveform

After the STD adjustment is complete, adjust the COMP 15K, COMP 31K, 33K RGB, COLOR TEMP FILM or STD and COLOR TEMP B&W for STD.

212

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PRO-610HD PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Main Contents of Memory Name of AssyAssembly Adjustment Location Adjustment ItemsAssembly Adjustment Location Guide If Mirror and ScreenSwitch with Front panelPosition PressControl Unit Other Offset modeKeys on the Remote Telop Blue Brightness AdjustmentInput signal Black Burst Input Deflection Yoke Adjustment 1Deflection Yoke Lean Adjustment 2Screen Center AdjustmentFocus Adjustment 1Focus Adjustment of Lens Assy 2Focus VR AdjustmentFocus VR VR1 Focus VRDigital Conv Assy Menu → Setup → Convergence → FullTest-cross Position Check Screen Size Adjustment 1Size Mode2Vertical Size Adjustment Size mode3Horizontal Size Adjustment About H. PhaseReference PRO-610HD SD-582HD5 PRO-510HD SD-532HD5Procedures Prior to AdjustmentConvergence coarse adjustment Screen mode Input signalCoarse Adjustment of the Green Waveforms adjustable in the coarse adjustment of the greenOffset Conver Data Numeric KeyFine-adjustment of the Green Pattern for each adjustment itemCoordinates where the cursor adjustment point is located Key No. `Adjustment Technique 1st step Color to be adjustedCoarse Adjustment of the Red 2nd step4th step 3rd stepFine-adjustment of the Red RV BVWhite Balance Adjustment 1Contrast Adjustment Coarse Adjustment and Fine Adjust- ment of the BlueConfirmation of Adjustment STD Offset Compornent 31, 33K Compornent 15KRGB DRV-R3Color/Tint Adjustment Adjustment Procedure of White BalnceBlue cyclically Color Temp Film for STDColor Temp B&W for STD Green cyclically Color Temp News for STDGND Panel AdjustmentProcedures Panel Adjustment for DTV PRO-610HD, PRO-510HD only Size Adjustment of the Panel Part of the 43 Normal Screen218 How to diagnose a failure Diagnosis MethodYES CONV. AMP AssyStatus Causes Check Items Probable Defective Parts Causes Check Items Probable Defective Parts AWV1800 Elite AWV1799 Elite Block Diagram of the Protection CircuitD915 D321 D923Disassembly How to remove the screen for adjusting Lens assembliesDisconnect the Anode Cable FBTWiring Diagram FBT Focus WireRear Section Video A/D Converter ∙ Block Diagram ∙ List of IC∙ Pin Function Pin Name Pin FunctionConverter ∙ Block Diagram Clkg ClkbVccd CompSenable IovccTtlgnd IogndSystem Controller IC ∙ Pin Function Mclkc MCSMras Mcas235 236 Vclk CLP1 CLP2HBLK1 HBLK2EM636327Q-8 SUB Video Service Assy IC3601, IC3604 PRO-610HD, PRO-510HD onlySystem micro-computer IC ∙ Pin Function Pin Name Pin FunctionSAA4990H SUB Video Assy IC3401 SD-582HD5, SD-532HD5 only 2M9 Field Memory IC ∙ Pin Function SAA4977H-K SUB Video Assy IC3403 SD-582HD5, SD-532HD5 only Besic A/D, D/A Memory Control IC ∙ Pin Function24LC128IP Digital CONV. Assy IC1410 24LC08BIP Digital CONV. Assy IC1656Pin Function 8Kbit Cmos Serial Eeprom Pin Assignment Top viewCM0006CF Digital CONV. Assy IC1401 Digital Convergence Correction IC ∙ Pin FunctionBvout GvoutRvout Bhout24LC32AIP Signal Assy IC2454 ML6420CS-3 Signal Assy IC7501Video Filter IC Pin Assignment Top view GndbCXA2094Q Signal Assy IC2701 US Audio Multi-channel Decoder IC ∙ Block DiagramSubout AUX1-RAUX1-L AUX2-LCM0010AF Signal Assy IC7703 D Inputs for Sub Video SignalsImage D/A output Main PLLSub PLL Dram I2C BusDigital Input TestSUB Video Assy IC3002 TK15420M Signal Assy IC7102, IC7302, IC7502MC33167TV Power Supply Assy IC204 Connecting VIDEO/AUDION Equipment ExplanationTo Watch TV To turn off the soundProgram Block V. Chip Function Mpaa RatingSetting the Program Blocking Level Mpaa Rating HOW to Remove Blocking from a Program in Progress Changing PasswordViewing TWO Screens Split screen MULTI-SCREEN FunctionPress the Search button Press Menu and select SET UP by Adjust the blue line Picture Adjustments Sound AdjustmentsChanging Screen Mode Special Notes265 Panel Facilities and Specifications Volume buttons TV Power button STANDBY/ON = CH Enter button Input DPO OFF Input Selector buttons TV, Input 1 to Input 273 Display and amplifier section Monitor
Related manuals
Manual 92 pages 6.09 Kb

PRO-510HD, PRO-610HD specifications

The Pioneer PRO-510HD and PRO-610HD are two advanced professional display monitors that exemplify cutting-edge technology in the realm of high-definition visual solutions. Designed for various applications, including broadcasting, live events, and video production, these monitors provide exceptional image quality and versatile features.

One of the standout characteristics of both models is their high-resolution display capabilities. The PRO-510HD boasts a 51-inch screen size with an impressive resolution of 1920 x 1080 pixels, ensuring sharp and vibrant images that meet the demands of professional users. The larger PRO-610HD features a 61-inch screen size with the same high-definition resolution, allowing for an immersive viewing experience.

These monitors leverage advanced LCD technology to deliver remarkable color accuracy and consistent brightness. With a wide color gamut, users can expect true-to-life colors, making these monitors ideal for color-critical applications. The brightness levels of both models reach up to 700 cd/m², ensuring visibility even in brightly lit environments.

Connectivity is a crucial aspect of any professional monitor, and the PRO-510HD and PRO-610HD are equipped with a range of input options. They offer multiple HD-SDI, HDMI, DVI, and analog connections, allowing for seamless integration with various broadcasting and production equipment. This flexibility ensures that users can easily connect their devices without the need for additional converters or adapters.

Another significant feature of these monitors is the built-in waveform and vector scope displays. These tools are essential for ensuring proper exposure and color balance, providing users with real-time monitoring of their video signals. The monitors also support various aspect ratios, making it easy to adjust the display according to specific project requirements.

Durability is key for professional equipment, and both the PRO-510HD and PRO-610HD are constructed with robust materials, ensuring longevity even in demanding environments. The monitors are designed for continuous operation, making them reliable for long hours of use whether in studios or on location.

In conclusion, the Pioneer PRO-510HD and PRO-610HD are powerful tools for professionals who require high-quality displays with advanced features. Their excellent image quality, extensive connectivity options, and integrated monitoring tools make them an attractive choice for anyone involved in video production or broadcasting. With their durable design and user-friendly operation, these monitors stand out as reliable partners in the visual media landscape.
Top Page Image Contents