Pioneer PRO-510HD, PRO-610HD service manual Volume buttons

Page 75

PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5

8RETURN button

Press to set the Projection Monitor to its initial mode.

Initial mode

Input selector:

Set to TV.

TV channel:

Remains at the last channel set.

VOLUME:

Remains at the last setting.

MUTING:

OFF

PICTURE

 

MODE:

STD

Parameters:

Set to 0.

3D Y/C LEVEL:

3

3D NR LEVEL:

3

COLOR TEMP:

STD

FLESH TONE:

ON

PURECINEMA:

HQ

SVM

HIGH

SOUND

 

MTS:

MAIN

Parameters:

Set to 0.

SURROUND:

OFF

SUPER BASS:

OFF

SCREEN

 

MODE:

NATURAL WIDE

V. POSITION:

Set to 0.

CC:

OFF

DPO:

OFF

SYSTEM IN/OUT

 

SPEAKER:

NORMAL

AUDIO OUT:

FIXED

SYSTEM MODE:

OFF

DTV OUT:

OFF (When the SH-D09 is connected)

∙When this button is pressed while adjusting the MULTI- POINT convergence, the MULTI-POINT convergence returns to the initial mode.

9VOLUME buttons

Press plus (+) button to increase the volume, press minus (–) button to decrease it.

0INPUT 4 jacks

These inputs are for Video Movie and VCR. Use RCA-type pin plug cords (the same as those used in Hi-Fi systems) and S- VIDEO cords for connections. When the audio source to be connected is monaural, connect the source to the L-(MONO) jack.

CAUTION:

Do not press any operation button on the Projection Monitor or the remote control unit while recording. Signals from the MONITOR OUTPUT jacks may be temporarily interrupted when a button is pressed.

ATTENTION

The Projection Monitor Receiver will not function properly in the following cases.

∙An electrical discharge in the CRT.

∙Lightning storms.

∙High static electricity environment.

∙Poor voltage regulation in the power source.

If the Projection Monitor does not operate properly, reset it as follows:

1.Turn off the power of the unit with the 4 MAIN POWER switch.

2.After approximately 1 minute, turn on the power with 4 MAIN POWER switch and 5 POWER button.

If the normal operation cannot be restored after the above treatment, immediately unplug the power cord and call your nearest PIONEER-authorized service center.

NOTE:

On rare occasions, an electrical discharge may occur inside the CRT. It makes a short, sharp pop and either no sound is produced or the volume level changes by itself. The SPLIT screen and SEARCH screen functions will be cancelled automatically if an electrical discharge occurs when this function is engaged.

267

Page 74 Page 76
Image 75
Page 74 Page 76
Contents PRO-610HD PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Name of Assy Main Contents of MemoryAdjustment Items Assembly Adjustment LocationIf Mirror and Screen Assembly Adjustment Location GuidePress Switch withFront panel PositionOther Offset mode Keys on the RemoteControl Unit Brightness Adjustment Input signal Black Burst InputTelop Blue 2Screen Center Adjustment Deflection Yoke Adjustment 1Deflection Yoke Lean AdjustmentFocus VR Focus Adjustment 1Focus Adjustment of Lens Assy2Focus VR Adjustment Focus VR VR1Menu → Setup → Convergence → Full Test-cross Position CheckDigital Conv Assy Size mode Screen Size Adjustment1Size Mode 2Vertical Size AdjustmentPRO-610HD SD-582HD5 PRO-510HD SD-532HD5 3Horizontal Size AdjustmentAbout H. Phase ReferenceScreen mode Input signal ProceduresPrior to Adjustment Convergence coarse adjustmentNumeric Key Coarse Adjustment of the GreenWaveforms adjustable in the coarse adjustment of the green Offset Conver DataKey No. ` Fine-adjustment of the GreenPattern for each adjustment item Coordinates where the cursor adjustment point is locatedColor to be adjusted Adjustment Technique 1st step3rd step Coarse Adjustment of the Red2nd step 4th stepRV BV Fine-adjustment of the RedCoarse Adjustment and Fine Adjust- ment of the Blue Confirmation of AdjustmentWhite Balance Adjustment 1Contrast Adjustment DRV-R STD Offset Compornent 31, 33KCompornent 15K RGBAdjustment Procedure of White Balnce 3Color/Tint AdjustmentGreen cyclically Color Temp News for STD Blue cyclicallyColor Temp Film for STD Color Temp B&W for STDPanel Adjustment ProceduresGND Size Adjustment of the Panel Part of the 43 Normal Screen Panel Adjustment for DTV PRO-610HD, PRO-510HD only218 CONV. AMP Assy How to diagnose a failureDiagnosis Method YESStatus Causes Check Items Probable Defective Parts Causes Check Items Probable Defective Parts Block Diagram of the Protection Circuit D915AWV1800 Elite AWV1799 Elite D923 D321How to remove the screen for adjusting Lens assemblies DisassemblyFBT Disconnect the Anode CableFBT Focus Wire Wiring DiagramRear Section ∙ List of IC Video A/D Converter ∙ Block DiagramPin Name Pin Function ∙ Pin FunctionConverter ∙ Block Diagram Comp ClkgClkb VccdIognd SenableIovcc TtlgndSystem Controller IC ∙ Pin Function Mcas MclkcMCS Mras235 236 Vclk HBLK2 CLP1CLP2 HBLK1PRO-610HD, PRO-510HD only EM636327Q-8 SUB Video Service Assy IC3601, IC3604Pin Name Pin Function System micro-computer IC ∙ Pin FunctionSAA4990H SUB Video Assy IC3401 SD-582HD5, SD-532HD5 only 2M9 Field Memory IC ∙ Pin Function Besic A/D, D/A Memory Control IC ∙ Pin Function SAA4977H-K SUB Video Assy IC3403 SD-582HD5, SD-532HD5 only8Kbit Cmos Serial Eeprom Pin Assignment Top view 24LC128IP Digital CONV. Assy IC141024LC08BIP Digital CONV. Assy IC1656 Pin FunctionDigital Convergence Correction IC ∙ Pin Function CM0006CF Digital CONV. Assy IC1401Bhout BvoutGvout RvoutGndb 24LC32AIP Signal Assy IC2454ML6420CS-3 Signal Assy IC7501 Video Filter IC Pin Assignment Top viewUS Audio Multi-channel Decoder IC ∙ Block Diagram CXA2094Q Signal Assy IC2701AUX2-L SuboutAUX1-R AUX1-LD Inputs for Sub Video Signals CM0010AF Signal Assy IC7703Main PLL Sub PLLImage D/A output Test DramI2C Bus Digital InputTK15420M Signal Assy IC7102, IC7302, IC7502 MC33167TV Power Supply Assy IC204SUB Video Assy IC3002 Explanation Connecting VIDEO/AUDION EquipmentTo turn off the sound To Watch TVMpaa Rating Program Block V. Chip FunctionSetting the Program Blocking Level Mpaa Rating Changing Password HOW to Remove Blocking from a Program in ProgressMULTI-SCREEN Function Viewing TWO Screens Split screenPress the Search button Press Menu and select SET UP by Adjust the blue line Special Notes Picture AdjustmentsSound Adjustments Changing Screen Mode265 Panel Facilities and Specifications Volume buttons TV Power button STANDBY/ON = CH Enter button Input DPO OFF Input Selector buttons TV, Input 1 to Input 273 Display and amplifier section Monitor
Related manuals
Manual 92 pages 6.09 Kb

PRO-510HD, PRO-610HD specifications

The Pioneer PRO-510HD and PRO-610HD are two advanced professional display monitors that exemplify cutting-edge technology in the realm of high-definition visual solutions. Designed for various applications, including broadcasting, live events, and video production, these monitors provide exceptional image quality and versatile features.

One of the standout characteristics of both models is their high-resolution display capabilities. The PRO-510HD boasts a 51-inch screen size with an impressive resolution of 1920 x 1080 pixels, ensuring sharp and vibrant images that meet the demands of professional users. The larger PRO-610HD features a 61-inch screen size with the same high-definition resolution, allowing for an immersive viewing experience.

These monitors leverage advanced LCD technology to deliver remarkable color accuracy and consistent brightness. With a wide color gamut, users can expect true-to-life colors, making these monitors ideal for color-critical applications. The brightness levels of both models reach up to 700 cd/m², ensuring visibility even in brightly lit environments.

Connectivity is a crucial aspect of any professional monitor, and the PRO-510HD and PRO-610HD are equipped with a range of input options. They offer multiple HD-SDI, HDMI, DVI, and analog connections, allowing for seamless integration with various broadcasting and production equipment. This flexibility ensures that users can easily connect their devices without the need for additional converters or adapters.

Another significant feature of these monitors is the built-in waveform and vector scope displays. These tools are essential for ensuring proper exposure and color balance, providing users with real-time monitoring of their video signals. The monitors also support various aspect ratios, making it easy to adjust the display according to specific project requirements.

Durability is key for professional equipment, and both the PRO-510HD and PRO-610HD are constructed with robust materials, ensuring longevity even in demanding environments. The monitors are designed for continuous operation, making them reliable for long hours of use whether in studios or on location.

In conclusion, the Pioneer PRO-510HD and PRO-610HD are powerful tools for professionals who require high-quality displays with advanced features. Their excellent image quality, extensive connectivity options, and integrated monitoring tools make them an attractive choice for anyone involved in video production or broadcasting. With their durable design and user-friendly operation, these monitors stand out as reliable partners in the visual media landscape.
Top Page Image Contents